What should I do if I get water in the phone? Practical recommendations and ways to solve the problem

By negligence you can do a lot. Particularly at risk are mobile devices, with which people now almost never separate. They are often dropped. And it's good if the phone fell on a soft surface. Even with the fall on the asphalt there is a chance that nothing terrible will happen. But if the device fell into a puddle, or even did not fall, and the soak in some other way, it's already unpleasant. In this situation, you need to act quickly, without hesitation. Therefore, you need to know the sequence of actions. What should I do if I get water in the phone?

What do not you need?

There are some strange methods, for example, stick the device in a bag of rice, which will draw out all the moisture. Another advise to completely fill the phone with alcohol. What should I do if I get water in the phone? Certainly not to follow such advice. All this is ineffective, and further it becomes clear - why.

The most dangerous liquids for phones are seawater, water with washing powder or, attention, jam. Yes, they drop it too. And still dangerous liquids in which there is an alkali, salts and so on.

Even if the water that gets into the phone is distilled, not letting the electric current flow through, then the garbage that is surely inside each device can lead to unpleasant consequences. What should I do if I get water in the phone? Immediately take immediate action. After all, even if you dry the device without analyzing it, then eventually all the tracks on the board will still oxidize and break down. A month later, irreparable problems can begin. The recessed phone will still work, but for a long time it can not live like this.

So, what sequence of actions is needed? What should I do if water gets into the phone? And you need to do the following:

• Remove the back cover and remove the battery.
• Shake off all visible drops.
• Find a dry rag or towel.
• Remove the housing and remove any liquid inside the device.
• The board should be washed with alcohol.
• The same is done with all the other parts of the metal (this can be done with a brush or in an ultrasonic bath).
• Dry the device for at least 12 hours.

Detailed description of actions

With the removal of the battery you can not hesitate for a second! What should I do if I get water in the phone? It is necessary to get it out of the water if it fell there, since even a couple of seconds is enough to get a significant amount of moisture into the headphone and memory card holes. Even worse, if it's water with a detergent. So housewives during laundry should clean their phones away. The battery must be removed as soon as possible, as a short circuit may occur. During the disassembly of the device, a SIM card and drive are removed. All this should be put on a dry towel.

Disassembly of the phone

Many users, of course, will carry the recessed device to the service center, but not all masters make quality repair of equipment. Especially if it's a wet phone. Some do only a part of the repair, after which the device can work no more than a month. Therefore, it is better to understand this issue and do everything with your own hands. After all, the user himself will treat his gadget much more carefully than a master who does not care about someone else's property. And with their "help" you can easily and irretrievably lose all valuable information.

To begin with, on the Youtube site, you need to find instructions for disassembling just such a phone model as the user. The video will show everything: from the type of latches to the number of trains. Sensory devices have fewer nodes.

What tools will be needed?

• Set with small screwdrivers, asterisks or hexagons. It depends on the particular model.
• A sharp scalpel, a mediator, or some thin plate that can be used to pick out the parts of the device's body.

Everything should be done slowly, very slowly and accurately. We must carefully disconnect all plumes, speakers and the like.

Cleaning from the inside

This process is probably the most painstaking. It is better not to use cotton, because it leaves too much pile. It is better to choose a cotton cloth or wipes.

Solvent can not be used in any case! In order to clean the device board, you can take from the medicine chest ordinary ethyl alcohol. After all, it is available.

It is necessary to remove the speakers, the microphone and the display. They then can only wipe the contacts. Outside, the body does not need to be rubbed with alcohol, as this can leave stains and stains, which will spoil the appearance of the device. The board itself can be dipped in alcohol. All pollution and oxidation are cleared from it. If you do not do this immediately and qualitatively, then after a while it will be too late, and you will need to solder it. If there is an ultrasonic bath, then the board after brushing can be dipped into it.

Drying from alcohol

The board after bathing is wiped dry from alcohol. This should be done very carefully. After the liquid evaporates, the solutes should not settle on the parts. The alcohol dries very quickly, but moisture can remain under the microchips.

After all the above operations, you can collect the phone and try to start it. Everything should work. This should save you nerves and money.

If the phone does not work, you can not do without visiting the service center. The main thing is to choose a good master. Recommendations of other people should help in this.

Water in the sensor

Sometimes it happens that the phone hit the water. What to do? In most cases, it needs to be replaced with a new one, since even small droplets are undesirable. The cost of the screen is not very high, and you can find it in specialized stores. There you can also ask to make repairs.

If you decide to replace it yourself, you need to do the following:

• Disassemble the device.
• Separate the sensor from the screen. If there is a sticky layer, then it can be wiped off with a fleece soaked in a liquid to remove varnish.
• Install the sensor purchased in the store.

Attention, before you buy it, you need to make sure that it's not a connector or a loop, because often due to corrosion, just spoil the contacts.

It happens that the water gets into the phone's speaker. What to do in this case? There is no choice: it only needs to be changed to a new one. The speaker is no longer subject to recovery. And if the phone got water? What to do then? Here fifty to fifty: either during the parsing and drying, the moisture in it will dry completely, or the sensitive elements will refuse to work and will have to carry the device to a service center where they will most likely say that the camera needs to be replaced.

Here such actions will help, if the mobile phone has got in water. What if this happens? The main thing, without panic. If everything is done correctly, then in a day there will be no consequences. But it's best to be attentive and make sure that the mobile does not come close to the sources of moisture.