Ice Chopper from the chainsaw with your own hands: scheme. Homemade ice pick for winter fishing

The chop saw from the chain saw with its own hands, the scheme of which is presented in the article, can be made with the help of our recommendations. This will facilitate the work of the fisherman. It is very difficult to use a non-automated device for drilling ice, this makes the process more labor-intensive. You can, of course, buy similar equipment, but it will cost much more, in addition, for those for whom fishing is just a hobby, such a purchase will not be worthwhile. As the most appropriate option is the use of chainsaw as the basis for the future tool. In the process of carrying out the work, it will be necessary to modernize the tool. This does not mean that the chainsaw is subsequently not usable, its master will also be able to apply if necessary.

Preparation of materials and tools

The chain saw with its own hands, the scheme of which will be shown below, can be made only with a certain set of materials and tools. Among them we can distinguish:

• Chainsaw;
• Icebreaker;
• Reducer;
• Plywood;
• Washers;
• Bolts;
• Nuts;
• Metal tube;
• The Bulgarian;
• Screwdriver;
• A jigsaw;
• Grinding machine;
• Drilling machine ;
• lathe;
• welding machine;
• drill.

Preparatory work before the icebreaker

It is necessary to prepare the entire set of materials and tools, otherwise it will not be possible to produce work. In this example, a gasoline saw, produced under the brand STIHL MS180, is involved. But when choosing an icebreaker, you can choose the diameter that suits you. The work will also require a reducer, which can be borrowed from the old MAKITA HP2033 drill. In the process, plywood is also useful, the thickness of which should be 20 mm, but it is preferable to prepare a metal sheet instead. As fasteners, which will act as additional components, you can distinguish nuts, washers, as well as bolts. The chain saw with its own hands, the scheme of which must be in front of you throughout the process, you will not be able to make, unless you prepare a preliminary head for 27 mm.

Recommendations for the manufacture of handles

The design will be supplemented by elements, among which - the handle, it can be made from improvised materials. For example, in such cases a metal tube is often used. But in order for the tool to be comfortable to use, the handle must be sealed, so it will not deliver unpleasant sensations, and wet hands about it will not burn. So, it is necessary to prepare any suitable for this warming material. You also need a tube, the length of which is 25 cm, you must choose the one that has thick walls. The example will consider the case where the former ISTANA luggage compartment shock absorber is used. It is worth noting that it is necessary to prepare a metal plumbing pipe 15 x 15 cm.

Features of gearbox selection to the tool

The chain saw with its own hands, the circuit of which can be developed independently or borrowed from this article, can be made correctly and expected to function properly if the gear is selected according to the rules. This is due to the fact that this element acts as the basis of any tool for drilling ice, made on the basis of a chainsaw. The reducer can be borrowed from old power tools. Thus, to make the right choice, it is necessary to be guided by some rules, among them - the gear ratio, which varies between 1: 25-1: 50, in addition, the rotation should be direct. Both the tail and the gear shaft must rotate in the same direction. If the ice fishing rods are made using the gearbox mentioned in the example, the tool will work correctly, since this gearbox has a gear ratio of 1:30. Reducers that belong to this type have a shaft that is a continuation of the motor rotor, which after that must be removed by means of a grinder.

Plywood processing

If you do not have enough plywood, then you can use two sheets, which must be glued together. So, if you have a sheet with a thickness of 10 mm, then you can get a cloth with more durability, using two canvases. In advance it is necessary to make a marking of holes, which will be needed for the installation of bolts, draws and pins. In addition, by means of a 45-millimeter drill bit, it is necessary to make a hole by placing it opposite the sprocket, except for it there must be one more, which is necessary for the nuts. All these manipulations are recommended to be carried out on a special drilling machine.

Recommendations for the location of the head

Making ice drills for fishing, you will need to work with the top edge of the plywood fabric, on which you want to make a groove, at the same time you can not do without a grinder. After the gearbox is applied to the workpiece, it becomes possible to determine at what distance the head should be. It is necessary to take into account the features of the used chainsaw, which has an asterisk for 6 beams. This indicates that it is necessary to apply a 27 mm head.

Then the head is attached by welding to the shaft of the reducer. Carrying out these manipulations, you must be careful and attentive. In addition, the head must be centered. If you admit even the slightest inaccuracy, this can cause irreparable damage to the chainsaw. When everything is done, you can proceed to fastening the reducer to the plywood, the last of which is fastened to the chainsaw beforehand. The next step is to activate the chainsaw and analyze the result of the work done.

Work on the screw and the features of the process

Homemade icebreaker can not do without the use of auger. To carry out the next stage, it is necessary to use a thick-walled tube, borrowed from the former shock absorber of the luggage compartment of the car. The shock absorber must be mechanically attached to the body using two bolts. It is necessary to work on an adapter, which will lead from the reducer to the screw. For its manufacture, it is possible to use a pipe from which it is necessary to cut a workpiece 15 cm long. After this, rings are welded on the piece. Do not forget that the adapter, too, must be carefully processed, using a lathe for this .

Handle making

If you decide to make an icebreaker yourself, how to make it, you need to know exactly. Thus, the design has yet to be supplemented with a handle. It must be picked up or done on its own. In addition, after you need to think about how it will be attached. In order to make it easier to use the ice-holder, it is possible to fix the handle from different sides. But from extra plywood you need to get rid of. The sealing material must be put on the handle.

If you are thinking about how to make an icebreaker from a chainsaw, then you should know that the handle can be strengthened by means of self-tapping screws. Plywood must again be subjected to processing using a jig saw. It is necessary to do such work accurately, but they are performed in order to get rid of all unnecessary things.

Replacement of plywood with metal

A winter ice-picker can be made after purchasing an already ready-made nozzle on the chainsaw. However, independent production of the tool will not only be cheaper, but it will be much more enjoyable to use your own work. It is possible to fully use the above instructions in the manufacture, however, as a single remark to this installation is the replacement of plywood with a steel sheet. This, as practice shows, will allow to obtain a tool with higher strength characteristics. This is due to the fact that the wood can not be compared to these qualities with steel. The latter is not subjected to deformation, in addition, it is not afraid of mechanical effects. The icebore drawing, compiled before the start of the work, will allow you to do the work correctly.

Carrying knives sharpening

In order for the icebreaker to work for a long time, its knives should be sharpened from time to time, for this purpose it is necessary to prepare a bar made of abrasive material. The working surface must be wide and flat. When purchasing, make sure that there are no potholes and chips on the surfaces. Sharpening of the knives of the icebreaker is made by a bar, the grain of which is medium or small. You can use sandpaper, which has a marking ranging from H4 to H6. Use the stone, which was used when sharpening more than 15 sets of blades, it is impossible, since it is covered with irregularities and chips. This indicates that it will not be possible to make a normal grinding.

The angle, under which the cutting edges can be located, can be changed somewhat. If it is necessary to drill soft ice or ice, in which there are inclusions of sand, the angle should preferably be 90 degrees. In this case, the knife will not excessively bite into the ice and stay sharp longer. If there is sand in the ice, then the blade must be prepared especially carefully. If you decide to use an abrasive bar for sharpening, then it should be placed on a table or a horizontal surface, reinforced to prevent it from slipping. To do this, you can apply a thin cloth of rubber or double-sided tape. Sharpening of the icebreaker knives at the first stage presupposes the elimination of existing burrs. To do this, the knife is located on a large edge on the surface for sharpening. When grinding the blade, move the blade in a circular motion. In this case, the clamp should be uniform. This will achieve high-quality sharpening.

Finally

The diameter of the icebreaker can be chosen by the fisherman individually, since this indicator will depend on the requirements for fishing. However, the remaining recommendations should be followed strictly. Only then will it be possible to achieve the expected result.