Tile adhesive Ceresit cm 11: characteristics, consumption and feedback

If you are interested in Ceresit tile glue, see 11, first you need to familiarize yourself with its qualitative characteristics. The feedback will also help you to understand whether this composition is suitable for carrying out the work that you intend to carry out.

Characteristics

The described composition is intended for laying stone and ceramic tiles, which differs by water absorption to 3%. The size of the product should not exceed the dimensions of 30 x 30 cm. The base should be pre-checked for strength, as for floors and walls. The mixture can be used both outside and inside the premises. Most often this glue is used in industrial and civil construction. If the surface periodically or permanently will be affected by water, then you will need a glue for the tiles "Ceresite cm 11".

Additional features

The manufacturer allows the use of the composition if it is necessary to lay the tiles, the water absorption of which does not exceed 3%. This applies to clinker, stone and granite products. However, at the same time, it is possible to produce work only inside buildings, on floors that will not be heated. If you have to work with the base, which is deformed, as well as with the screed, heated during operation, it is necessary to add a liquid elasticizer to the composition. This also applies to other complex reasons.

Customer feedback on technical characteristics

Ceresit tile adhesive 11 see, as consumers note, can be used for a wide range of temperatures. However, do not start work if the thermometer's column has dropped below +5 degrees. The manufacturer does not recommend starting tile laying operations if the air temperature is above +30 degrees. Specialists of their work emphasize that it is important not only to observe external conditions, but also to use high-quality adhesive composition, but also to prepare it correctly. Thus, for 1 kilogram of dry composition you need water in the amount of 0.24 liters.

If you use Ceresit tile adhesive, see 11, it is important, as noted by experienced home masters, to anticipate the consumption of the mixture in advance. This parameter can vary from 1.7 to 4.2 kilograms per square meter. It is important to remember that after the preparation the solution will retain its properties for 180 minutes, while the open time of operation is fifteen minutes.

It is worth listening to those consumers who have already used this adhesive composition. They mention that it is possible to adjust the position of the tile after it has been put in place, within 20 minutes. You can start filling up the stitches in a day. All buyers who used a frost-proof composition, say that the Ceresit tile adhesive, see 11, the flow of which was mentioned above, can undergo 100 cycles of freezing and thawing. In addition, you can use this composition with a very wide temperature range. The glue can be operated at -50 to +70 degrees.

Reviews about the positive features

The described adhesive composition is very resistant to high humidity, in addition, it is excellent undergoes temperature changes. Buyers who purchased the glue for repair, note that it is very convenient to use. Most specialists characterize this mixture as an adhesive that has high adhesive properties when it comes to vertical surfaces. It can be used without fear that it will represent a fire hazard. For human health, this mixture is not harmful. Most household craftsmen choose this product for the specified reasons.

Scope of use

Ceresit tile adhesive, see 11, reviews of which you can read above, is intended not only for strengthening of stone and ceramic tiles. It is acceptable to use when working with facades, socles, entrance panels, terraces, parapets, balconies, as well as roofs in use. If there is a need to use this compound in indoor pools, then you should add an elasticizer. Excellent contact with the mixture of chipboards, plasterboard, OSB plates, as well as other deformable bases. If you decide to use the glue "Ceresit 11" (Ceresit cm 11) for tiles, it is first necessary to find out what characteristics the base has. This product can be used for manipulations performed on gypsum substrates. Work with glue can be in tandem with old tiles.

Cost of the composition

Adhesive for Ceresit tile cm 11, whose price is 260 rubles, has a wide scope of use. It is important to purchase a composition that is properly stored, and also has an intact packaging. The above amount will have to be given for a bag, the volume of which is 25 kg. Before purchase, check if the shelf life of the product has expired. If such a circumstance exists, then it is worth to refuse the purchase of glue, even if the price is lower in comparison with that offered by competitive sales points.

Features of use

Ceresit tile adhesive, see 11, the price of which was indicated above, should not only be properly selected, but also used in technology. Before starting the manipulations, you need to prepare the surface well, which involves cleaning up stains, dust and dirt, as well as oil or paint. Glue should be applied without preparation, if it is necessary to work with a concrete, plaster or cement surface. Such bases have an excellent absorbency, which is why they should be moistened beforehand. Otherwise, you will encounter a consumption of glue that exceeds many times the declared by the manufacturer.

Tile adhesive Ceresit cm 11, the characteristics of which are presented in the article, should be diluted before use with water, mixing the mixture until a uniform mass is formed. It should not form lumps. The surface treatment of products with glue should be done with a grater, which has denticles. This will fill all the voids and ensure a quality fastening of the product to the base. After the tile was in place, it should be slightly pressed into the surface, moving slightly from side to side.

Do not rush to laying the next product, as it is necessary to make sure that the previous one is mounted correctly and corresponds to the horizontal level. The latter should be checked using the building level. Only with this technology will it be possible to achieve an ideal result, regardless of whether work is carried out on a vertical or horizontal surface.