Primer "Cinotan": technical characteristics, properties and instructions for use

Protection of metal structures and industrial structures against corrosion is a good consideration for the future, this saves on the operation and repair of structures. As such a tool is "Cinotan", the technical characteristics of which will be described below.

This anticorrosive composition provides protection even in conditions of high contamination by industrial emissions. The composition can be used in all microclimatic regions, types of atmosphere and categories of accommodation. The coating is resistant to contact with petroleum products and oil, sea and fresh water, as well as aqueous solutions of salts. Use "Zinotan" can be used as an independent coating or as a primer in combination with other materials.

Specifications

"Cinotan", the technical characteristics of which must be studied before purchasing the product, is gray, the hue is not standardized, and the dried coating has a matte surface. The thickness of the dry layer can vary from 40 to 80 μm. Impact strength is 50 cm, adhesion is 1 point.

The flexural elasticity is 10 mm, and the thermal resistance of the coating is 150 ° C. "Cinotan", the technical characteristics of which will be interesting not only for professionals, but also for the ordinary consumer, has a thixotropic viscosity in the range of 2, 9-3 g / cm ³ . The mass fraction of non-volatile substances varies from 86 to 88%. Consumption for a single-layer coating varies from 195 to 390 g / m ² . Up to 3 degrees, the layer will dry for 2 hours, while the ambient temperature can vary from 20 to 22 ° C, relative humidity can be 65%.

Main features and properties

The application of "Cinotan" is possible without restriction on seasonality, while the external ambient temperature can vary from -15 to +40 ° C. The composition is completely ready for application, which indicates ease of use. The layer is resistant to aggressive media, in addition, it has a long service life.

Use "Cinotan" can be used for the anticorrosion protection of transport facilities and bridges, chemical and oil and gas industry facilities, and also for metallurgy. The composition is compatible with some compositions of the type "Ferrotan", and it can be used with epoxy, acrylic, polyurethane and vinyl bases.

Instructions for use: Surface preparation

"Cinotan", the technical characteristics of which you should be aware of before using it, is applied to pre-prepared grounds. The latter should be degreased, and then perform abrasive cleaning to the second degree. The surface must be rough, and if it is a hot-rolled steel, manual or mechanized cleaning up to grade 3 is permissible. On a smooth surface, the application without roughening is not allowed. The substrate must be dust-free before using the mixture.

Features of use

Primer "Cinotan", the technical characteristics of which were presented above and help you avoid mistakes during the work, is a composition that should be well mixed until smooth. If necessary, the mixture is diluted to the working viscosity before use. In field and factory conditions, the application should be carried out at the recommended temperature range, and the relative humidity at the time of application may vary from 30 to 98 ° C.

If it is intended to form a multilayer coating, then each subsequent layer should be applied after the previous one has dried. It is necessary to wait for release. You can check it by pressing your finger on the cover. If the trace does not remain, then you can continue to work. Sensations of stickiness should not be. The composition should not be in contact with air in open containers for a long time.

The technical characteristics of the coating "Cinotan" indicate that the subsequent application of coating layers of compositions, varnishes and enamels should be carried out after 4 hours or more. In this case, the temperature of the external environment should be 20 ° C, relative air humidity - 65%. Dry the coating is necessary under natural conditions. If during this stage the humidity is reduced, the drying period will be increased. Sometimes this mixture is used together with drying accelerators for polyurethane paint materials, however, before the start of operation, it is necessary to withstand the time, which is 7 days. This is true when it comes to aggressive environments.

Safety measures for application

"Cinotan", the technical characteristics, the properties of which were presented above, should be applied taking into account the safety measures. The master should use personal protective equipment, namely:

• Mask;
• Points;
• Respirator.

When evaporating and getting the mixture on the skin, do not inhale solvents. Application should be carried out with sufficient ventilation. It is necessary to exclude the penetration of the primer into the respiratory tract, as well as the mucous membranes of the eyes. The product is considered a fire hazard material.

Conclusion

"Cinotan", technical specifications, the price of which you should be interested, if you are planning to purchase this primer, is a tool that reliably protects metal structures. You can buy this mixture for 420 rubles. Per kilogram. Use the composition is quite simple, you need to use a roller or brush for this, and "SOLV-UR" acts as the recommended diluent. To wash the equipment, use the same solvent or oil solvents.

If you plan to use air spraying technology during application, the diameter of the tool nozzle can vary from 1.8 to 2.2 mm. At the same time, the pressure can reach a limit of 0.3 to 0.4 MPa, which is approximately 4 bars. The amount of diluent that was mentioned above can be used in a volume of 5% by weight.