Homeliness, Building
"Hydrotex-B": user's manual, feedback. Materials for waterproofing
When erecting any building, builders pay special attention to the protection of the foundation. It is necessary to prevent the influence on the construction of an aggressive underground environment, water, various compounds - penetrating into the concrete, they destroy it. In a few years the base of the building will begin to crack, and then collapse. To prevent this, the special mixtures produced by Russian producers will help. Among them is the penetrating waterproofing "Gidroteks-V". What is this material, what are its features and advantages? And what do they say about the mixture of "Hydrotex-B" reviews of specialists and consumers?
Description of the material
Several modifications of the "Hydrotex" material are produced:
- "P" is universal.
- "U" - an antifungal effect.
- "B" is a restorative.
- "B" - fast-hardening.
Scope of application
In many other areas, too, use "Hydrotex-B." Examples of application:
- Industrial hydraulic engineering. The material is indispensable in the construction of water tanks, sedimentation tanks, treatment plants, dams, etc.
- Marine construction. For the erection, repair and restoration of various structures. These are piers, breakwaters, etc.
- Industrial engineering. Collectors, tunnels, bridge supports, pumping stations, concrete recessed premises and many other objects need protection from moisture.
- Power engineering. Waterproofing provides protection to concrete structures.
In other words, you can use the mixture in many cases. But not in all. There are facilities on which it is inadmissible to use "Gidrotex-B". The instruction for use states that the mixture is not suitable for providing protection to those structures affected by mineral acids.
Advantages of the material
- Durability.
- Ecological cleanliness.
- The ability to create a very durable coating.
- Possibility to significantly increase the operating time of the structure.
- High adhesion to the surface to be treated.
Equally important is the safety of the mixture, since it is created on a cement basis without solvents. Confirms the safety of the slurry permit to use it in the domestic drinking industry. This is stated in the document GHS No. 77.01.03.570.P.17806.04.09.
Another important property of the waterproofing solution is economy: the work can be carried out inside buildings, which allows not to worry about external expensive insulation. Thus, using materials for waterproofing the brand "Hydrotex B", you can forget about the repair for a long time, which saves money and labor.
How to prepare the mixture for work?
- Take from the package and grow only the amount of the mixture that will be used in the next 30-35 minutes.
- Calculation for 1 square. M - 2,5 kg.
- The mixing capacity should be comfortable to avoid wasting time on the preparation process.
- The water should be warm. It should be taken 20-25 percent in relation to the weight of the mixture.
- Stir can be manually or by using a low-speed mixer.
- Leave the solution for 5-6 minutes, then stir again.
- The material is then ready for use when it is plastic, homogeneous.
Features of use
- In the masonry, the joints should be widened by at least 0.5 cm.
- At joints of structures, the joints should be widened at least 0.2 cm and at a depth of 2 cm or more.
Next, the surface must be rinsed with water to remove any remaining cleaning residues. If there is a bare reinforcement in the machining area, it must be cleaned so that a metallic luster appears.
The prepared surface should be clean, rough to the touch and abundantly moist, with marked places of fistulas and leaks.
Restoration of watertight structures
After preparation, the surface must be primed with a waterproofing solution. To rub the mixture, a fly brush is usually used. Then with a spatula, or you can apply the method of spraying the material, filling up the seams until the very beginning of the crack. The minimum application layer is 2 mm. After a day, the treated area should be checked - whether there are any new leaks. Using drainage tubes, remove moisture and after 72 hours remove them.
If the structure structure is loose, porous, it is necessary to repeat the treatment using the same materials for waterproofing. When the next layer of mortar also dries, it is possible to carry out finishing works (gluing of wallpaper, whitewashing, painting). But before proceeding to finish, you need to wash the surface with a 5% acetic acid solution.
Opinions and recommendations of specialists
Experts recommend that you carefully consider the peculiarities of handling the mixture of "Hydrotex-B". Instructions for use - the most important document, which must be studied before starting work. Ignorance of many subtleties will lead to the fact that the claimed characteristics can change, the material will be wasted, and the main task - to restore the waterproofness of the structure - is not solved: the protective coating will peel off.
Is "Hydrotex B" really so reliable and reliable if all the recommendations are observed? Feedback from those who have had to work with the mixture confirm that there are practically no problems, the use of the solution provides an excellent result, and due to the fact that it is possible to work from inside the building, there is no need to unearth the foundation, which makes the whole process much easier.
Similar articles
Trending Now