How to make a hydrocycle by yourself?

For active recreation, hydrocycles of various types are perfectly suited. Modern models are quite expensive. How to make a hydrocycle by yourself? First of all, it is worth familiarizing yourself with the device model.

Simple Jet Ski

The conventional model includes a body, a frame, supports, a motor and a stringer. Many hydrocycles use a trawl. Its fixation is carried out on brackets. Filler is often used from foam. The decks of the models can be of different lengths. If we consider the upper stringer, then it is installed with the fairing. Also it must be remembered that the bottom of the models is covered with a protective layer. The keel part at the hydrocycles is allocated with wide stops. A hole is provided for the steering shaft on the housing. In case of breakdowns, repair of the hydrocycle with your own hands can be done using a small set of tools.

Boat hydrocycle

A boat can be assembled with your own hands. For this purpose, the lower part of the housing is first prepared. Nasal handrails can be cut yourself. While working on the stringer, you will need a Bulgarian. A grinding machine is used to sharpen the bottom surface. Particular attention at this stage is paid to the keel section. Pontoon for a hydrocycle with your own hands can be made from bars. The upper part of the case is fixed with brackets. The hole under the steering column can be made with a jigsaw. In the end, it remains only to install the motor.

Two-Float Model

To assemble a two-float hydrocycle with your own hands (photo shown below) is possible only on the basis of a wide stringer. The deck in this case should be fixed on the racks. At the beginning of the work, the frame is prepared directly. The upper stringer can be fixed on brackets. As a filler, experts recommend using foam. The lower stringer should be riveted. It is allowed to apply the profile D16 under the hook.

Three-Floating Model

The three-float hydrocycle with its own hands is made with bow handrails. Many models first of all attach the end wall. After that, you can fix the bottom stringer. Trapezium in this case is selected a small width. The top stringer is installed last. The trailer for a hydrocycle can be made from metal sheets with thickness from 1.5 mm. The fairing of the nose should be selected with a small thickness. Pads are most often used from foam. It should also be noted that during work, attention should be paid to the steering column. The hole for the shaft can be made with a jigsaw.

Device with one transom stop

To do with one stop hydrocycle with their own hands is very simple. For this purpose, a long stringer with a small profile is selected. The bow rail is attached first. It is more expedient to make overlays from a foam plastic. Also it should be noted that experts advise not to install the upper stringer immediately. At the beginning of the work, the deck is fixed. Lining is allowed to paste a small width. The keel part of the hydrocycle must be well protected.

To this end, experts use fiberglass. In this case, the filler is usually used from foam. Plywood can be used directly for the casing series C5. The bottom is most often treated with a grinder. Strings are to be installed at the top of the stringer. Trench stops are fixed in the keel section. In case of malfunctions, repair of the engine of the hydrocycle with your own hands can be done by removing the rear pillars.

Model with several transom stops

To do with several stops the jet ski with your own hands, you will need a wide rack. First of all, the lower part of the stringer is prepared. At this stage, the surface of the material is processed by a grinding machine. Many experts advise the filler to be used from foam. In the back of the stringer, the lining is fixed. The onboard stringer is attached to the brackets. It is also worth noting that a hydrocycle will require a frame. The bilge bar can safely take the D16 series. During the installation of the deck, special attention should be paid to the skin. At the end of the work, a hole is made for the steering column.

Hydrocycle with straight strips

Make a model with straight overlays is quite simple. For this, the stringer is used with a low profile. For the purpose of assembling the hydrocycle, the deck of the model is first prepared. Next, you'll need to install the bottom stringer. Experts do not recommend using a cheap seal. The bow rail is attached to the bracket. The bottom of the hydrocycle should be carefully cleaned with a grinding machine. Directly overlays are installed in the side of the stringer. A hole under the steering column can be made at the end of the robots.

Model with oblique overlays

To make a hydrocycle with oblique overlays it will turn out only on long stringers. Begin the assembly of the model is based on the length of the racks. If you select small stops, the trapezoid can be used with a low profile. Before installing the lower stringer, the bottom of the hydrocycle is completely pasted. In this case, you can immediately make a hole under the shaft to control the model. Decks in this case are installed on racks. Sheeting is most often attached to glue. The upper stringer is recommended to be fixed on the slats. At the end of the job, it remains only to secure the trawl. Repair of the body of the hydrocycle with its own hands is quite difficult.

Model with fiberglass bonding

To make a hydrocycle with fiberglass bonding is very easy. Stringers are allowed to use different lengths. At the beginning of the work, a board is prepared under the deck. It is recommended that the bottom is well polished. Experts say that the upper stringer is better to use with a small profile. The end wall must be fixed at the base of the frame. The plywood for these purposes is suitable with the C5 marking. The lining for the hydrocycle is made of foam. Experts advise carefully to clean edges of stringer. It is also important to carry out the installation of the steering column. For this purpose, a hole for the shaft is extended in the deck.

Double radome device

If necessary, you can make a model with a double fairing yourself. Begin assembly of the device should be standard with the workpiece of the racks and the future bottom of the model. The lower stringer can be fixed on brackets. The upper patches are glued along the rim. Many experts advise for a hydrocycle to use the plywood of the C5 series. Also worth noting that the cutout under the shaft can be done at the end of the robots. Pasting should be done very carefully. In this case it is important not to damage the integrity of the stringer. Trenches for this type of jet skis are suitable with plating. It is also worth noting that the aft part can be made with a sealant.

A model with a long stringer

Devices with a long stringer can be made on the basis of a wide frame. For this purpose, not only the stringer is harvested, but also the board under the deck. Separately plywood is selected under the rack. The lower stringer is fixed on the bracket. The fairing should be glued strictly horizontally. It is also worth noting that experts advise using large rivets. The hole under the shaft is made with a jig saw. To cut the upper stringer, you need a bulgarian. Trenches are allowed to be made from ordinary plywood. To install the steering rod will require several holders.

Device with short stringer

A model with a short stringer can be made independently. For it fit transoms of different profiles. It is recommended to begin the assembly of the modification from the preform of the supports. A transom will require a small stand. Plywood can be used series C5. Experts say that the filler can be taken from the foam. To install the overlays, glue is used. The keel part of the hydrocycle should be carefully cleaned. The upper stringer on the model is installed using brackets. The bottom of the hydrocycle is important to thoroughly polish.

Device with longitudinal versions

It is very difficult to make a model with longitudinal editions. The main problem in this case lies in the selection of the stringer. For a hydrocycle, a part with only a high profile is suitable. If necessary, the rack can be made independently with the help of a Bulgarian. It is more expedient to apply the C5 series to the plywood. Experts say that the nose rail should be done at the end of the work.

The keel part should be behind the editors. The upper stringer is fixed to the brackets. The end wall must be with overlays. As a filler is advised to use foam. It is also worth noting that experts recommend using a wide mount for the transom. All this is necessary in order to remove the load from the keel part of the hydrocycle. In this case, the strength of the frame will be greatly increased.