Equipment stand with own hands made of wood

Usually for years of life a large quantity of equipment is accumulated, which should be compactly and preferably aesthetically placed. All equipment must be located nearby, so the best placement option will be a rack for the equipment.

Buy it in a store is much easier than doing it yourself, but store racks are usually a TV cabinet with a shelf for a VCR. Now it is already irrelevant, as modern TVs are hung on the wall, and VCRs have long been in the past.

You can have 2-3 units of different equipment, and the fans can listen to cool music up to 6-7 of all kinds of instruments. By making a stand for the equipment with your own hands, you can safely arrange everything that is available in the apartment.

Materials and requirements for the rack

Electrical equipment has a significant weight, so the regiment must be strong. From the back panel comes a lot of wires, so it should be on the back side of the open. Since the stand for the equipment occupies a central place in any living room, it means that it must be beautiful and original.

You can execute it from different materials. Brew from strong metal corners, collect from galvanized profile. You can make a rack for the equipment from plywood, fiberboard, MDF and wood. An interesting option is the combination of materials. The legs can be metal, wooden, from plastic tubes. Well, if the wheels are installed from below, because behind the bar, where the bundle is located wires, will collect dust. Moving the shelf on the wheels, you can wipe the floor, and check the wiring. Very comfortably.

Double stand

In order to make this set of two units, it is necessary to have boards of coniferous wood, wooden beams, stain, lacquer, metal legs and screws for wood, sandpaper, joiner glue D3, wigs. First you need to draw a drawing of the future design. Since the TV is located on a rectangular shelf, its length should protrude by a few centimeters from the edges of the screen on each side. The boards of the required length are trimmed for two rectangular shelves and three square. Then the side strips are smeared with joinery glue and tightened by the wigs until it is completely solidified. At a temperature of more than 8 degrees, the adhesive dries for about 40 minutes. If the temperature is lower, then glue does not take, you can not do this. It is best to seal and leave the workpiece for all night.

The finished shields are carefully scoured by sandpaper No. 80, then No. 120, at the end No. 180. Everything is covered with stain. Choose the color of your choice. Then it is covered with a layer of soil. After drying, rub once more nazhdachkoy number 180, as the pile will rise from the ground. The last stage will be varnishing.

Next we prepare square wooden beams. Under the upper shelves, the corner is cut with the letter F in the half-tree, under the middle and bottom - with the letter P, also in the half-tree. After fitting the shelves to the legs and drilling the screw holes, repeat the painting procedure for the legs. After assembling the shelves, turn them upside down and fasten the metal legs. The stand for the equipment made of wood is ready.

Stand with stand for the speakers

The principle of manufacturing the shelf is very similar to the previous model, only the rack consists of 4 shelves, if the width allows, then the boards can not be glued. Shelves are cut into the legs also in a half-tree, only they are painted black. You can take any other, according to your desire. The stand stands directly on the wooden legs. To the floor is not scratched and you could move the rack, they are glued on felt, cut to size.

For pillars under the columns, you need to cut 2 large and 2 small squares. On the rail they are fastened with screws. The stand for the equipment and with two stands under the speakers is ready.

Combined rack

The easiest and fastest assembly rack for the equipment is made from cut-to-size sheets of chipboard, preferably laminated, pipes of the same length and round flanges. Also, several meters of edge, iron, 3x16 screws, screwdriver are needed. In workshops for sawing chipboard give the necessary dimensions to the master, and he makes accurate cuts on the professional machine. There you can order and glue the edge, but it will cost an order of magnitude more. If you want to save money, then at home with a simple hot iron it is very fast to paste it yourself.

After the sheets of chipboard are delivered home, the rack assembly begins. First, places are carefully marked for screwing the flanges so that the post is symmetrical. When everything is marked up, let's get to work. On the screws sit flanges, 6 pieces per shelf. On two middle shelves this is done from two sides. On the bottom shelf on the bottom 4 screws for furniture are fastened. Then the tubes are inserted, the next shelf is put on top, and so on.

Stance with the use of artificial aging

Now very fashionable furniture with aging from thick "brutal" boards. Cut out the same size boards for a size of 50 mm, for the side - 2 small rectangles. The rack is assembled on dowels (round sticks). To do this, first clearly measure and drill holes on the sides and on the shelves themselves, not through and through. Ready wooden dowels are sold in the store. Usually they have a diameter of 8 mm, but there are also 12 mm. We take a thicker, since the shelf is voluminous. At first everything is assembled without glue.

After fitting all the details are sorted out, and the most difficult thing begins - painting under the old days. To do this, we take the turbine, put on it a metal brush and process the wood. The brush removes soft layers and leaves hard. The brush on the turbine changes to plastic and small burrs are removed. Then paint with stain. Then comes the treatment of nazhdachkoy, but not much. Then cover with a layer of soil, we clean the nest of the raised pile, at the end we open with varnish. After drying, the rack is assembled into dowels, already with glue. At the bottom of the wheels are screwed.

Original stand for equipment from wood with own hands

To make this shelf, you need a circular saw with a slope to cut out the triangular legs for the shelf. The glued shields are cut to the size of future shelves. The stitches on them are attached to the dowels already known to us so that the connections are not visible. In order for the legs to stand steadily, the groove is pierced by a groove from one side and the other. The resulting rack is completely collapsible. It can be made as desired from 4 parts or set side by side (2 + 2).

Run a rack for the equipment with their own hands on the photos presented on the site, it's very simple. We wish good luck and creative success!