Electroactivator of water AP-1: circuit, reviews, instructions. Electric water activator with own hands

"A fairy tale is a lie, but there is a hint in it, a lesson to good fellows." Many generations heard these words in their childhood. They sounded almost in every folk tale. And in the same tales often referred to as "living" and "dead" water. And who would have thought that this was not fiction at all? The dead, however, living water does not resurrect, but it happens that it will not die. And to get it is not so difficult, and not in small vessels (bottles). And you need something very small - the electroactivator of water.

"Living" and "dead" water

Getting "live" and "dead" water is the process of electrolysis of ordinary tap water. That is, you do not need to go to the raw materials for the far end of the earth, it's only necessary to stretch out your hand.

"Living" (catholyte) is water with a negative potential, which has a more alkaline structure. It stimulates biological processes, its main properties are increased solubilizing and extracting ability and absorption-chemical activity. And its taste is alkaline, soft, like a clean rain. Living water quickly loses its healing properties, it can be stored for no more than seven days in a hermetically sealed container in a dark place. In the body, it stimulates the metabolism, improves digestion and appetite, raises blood pressure, fresh wounds heals quickly.

"Dead" (anolyte) - water with a positive potential and an acidic structure. Biological processes, it slows down, so it is a powerful antiseptic and preservative. The name of this water should be used in inverted commas. What it is dead, if it struggles with microorganisms and fungi, increases the shelf life of vegetables and fruits, lowers blood pressure, reduces pain in joints, is an excellent prophylaxis for catarrhal diseases, helps with fungal diseases of the skin and intestinal disorders.

The liquid from the tap (it can not always be called water) passed through the electroactivator of water can serve for various household purposes, for example, to increase the productivity of animals, stimulate the growth of poultry and plants, disinfect seeds and accelerate their germination; Fighting insects and pests in the house and garden; Sanitizing, sterilizing dishes, washing the laundry of a sick person and much more.

A list of diseases in which activated water helps, if not infinite, is very long. Here and tonsillitis, and gastritis, and hepatitis, and burns, and inflammation of the liver and large intestine, and dysentery, and chronic fistula, and many more.

Getting "live" water

The first description of the preparation of living water amazed, if not by the complexity of the preparation, then exactly the stretch of the process over time is accurate. The usual water first had to be defended for several hours, then boiled with a "white key", quickly cooled, preferably in drift or ice water, for two days on the flint, drained, without using the lower layer with harmful impurities, frozen in the same pan until The first ice that needs to be removed and discarded, again freeze by two thirds, in the layer that is formed, make a hole through which it is necessary to drain water with a high salt content, ice to defrost. As a result of all manipulations, we obtained live water.

Now the household electroactivator of water AP-1 is coping much faster. However, it is better to pre-clean the water in a reverse osmosis filter or with a distiller. And it is very good, if it after that it will be possible to slightly mineralize, insist on mountain quartz and silicon.

Water activator

Electric water activator AP-1 is a compact, light and easy-to-use device that allows to get activated water in less than an hour - both "live" (catholyte) and "dead" (anolyte).

To operate it, you need a household electric main with a voltage of 220 V and water itself.

Similar devices are produced by many companies, so when buying it, you need to make sure that the device has to be certified.

The combination of water and electricity requires, in accordance with the state standard, a high class (not lower than II) protection for electrical safety.

The hygienic safety of the device must also be documented.

Package Contents and Specifications

Electroactivator of domestic water - a neat little device weighing not more than 2 kg, is sold in a package, in which, in addition to the apparatus itself, a clear instruction manual, fuse-link (fuse for 1 A) and a small measure for table salt.

The total power consumed by the device is 70 V / A. In operation, AP-1 consumes about the same amount of energy as a single 40-watt light bulb.

Current strength during electrolysis is from 0.2 to 0.7 A.

At the same time 300 ml of anolyte and 900 ml of catholyte are prepared. The process should last no more than 40 minutes, because after that the acidity of water (pH) does not change anymore, and the power supply and liquid in the device are heated.

Device construction

The AP-1 water activator itself consists of a main tank into which a ceramic glass is inserted, an upper cover with electrodes and a power supply unit.

Capacity of transparent food plastic is used to make "living" water. In it in the process of electrolysis, catholyte is formed. On the side surface there are marks - special arrow-pointers.

The glass is the diaphragm between the cathode and the anode and serves as a "dead" water tank. In it anolyte formation takes place.

The removable cover in the lower part has a base made of insulating material. There are electrodes in it. Two black ones are anodes with a chemically resistant coating. Two light - cathodes from food stainless steel. Special materials protect electrodes from electrochemical destruction during operation.

The top cover is smooth, only the top is equipped with a light indicator, indicating if there are any voltages on the electrodes, and there is a holder for the fuse on the side surface, so the arrow-pointers on it are clearly visible.

Principle of operation of the device

Electrochemical treatment of water (electrolysis) leads to a sharp anomalous change in the catalytic activity and physical structure of water. Under the influence of an electric current in water, highly active metastable particles are formed, and the system of intermolecular interactions changes.

Cathodic electrochemical treatment of the liquid leads to the formation of highly soluble potassium and sodium hydroxides; Increases the pH; Formed hardly soluble calcium and magnesium carbonates; In insoluble hydroxides are converted almost completely ions of heavy metals and iron. This reduces the electrical conductivity and surface tension of water, it reduces the oxygen and nitrogen content.

Electroactivator of water is an instrument in which both cathodic and anodic treatment of a liquid occur simultaneously.

In the process of anodic electrochemical treatment, stable and unstable acids are formed - sulfuric, hydrochloric, hypochlorous - and persulphuric, oxygen-containing chlorine compounds. This increases the acidity of water and electrical conductivity, decreases the concentration of nitrogen and hydrogen.

Instructions for the preparation of activated water

Cooking "live" and "dead" water in the activator is simple and quick. A ceramic glass is placed in the main container in the center, then water is poured: into the glass to the top, and into the container on the finger below the edge of the glass.

The top cover is installed so that the marks (arrow marks) coincide on the side surfaces of the container and the lid itself. If the glass is installed accurately and the lid is correctly inserted, the anodes (black electrodes) are lowered inwards, and the cathodes (light electrodes) are outside the glass.

The lid must be tightly seated, until it stops. The plug is plugged into the power outlet and the start time of the device is detected. At the same time, the indicator starts to glow, and through the transparent wall of the container you can see bubbles of gas formed on the cathodes.

The electric water activator AP-1 should work for at least 10 minutes. The longer it works, the higher the concentration of the resulting solution.

After the end of the activation time, the device is disconnected from the socket, the lid is carefully removed from it (it can not be turned over), a glass with an anolyte is removed from the container. Then, from the glass, and from the tank "live" and "dead" water poured into the prepared dishes. That's all.

In this process, a measuring spoon for table salt is not used. It is used when it is necessary to increase the level of mineralization of a liquid to increase the current of electroactivation. In this case, a light solution of common salt is poured into the beaker, which is obtained by dissolving 1 g of fine salt in a liter of water.

To ensure that the activation current is not excessively large, mineral or salted water can only be poured into a glass.

Use of activated water

Attached to such an instrument as the electroactivator of water AP-1, the instruction describes in sufficient detail not only the operating principle of the device and the order of operation and maintenance, but also provides an explanation of what pH is, how to obtain the desired values, and how to use catholyte and anolyte .

Water as raw material differs in its composition and degree of mineralization. The instructions of the device give tables of the concentration (pH) dependence on the preparation time of solutions. However, it is clarified that the data are based on the fact that the pH is 7.7 for the initial liquid.

For "dead" water, the pH value of the pH varies from 3 to 5.5, and for "live" water it ranges from 8.5 to 10 units. And the longer the operating time, the lower the pH for anolyte and higher for catholyte.

Electric water activator with own hands

There are many options for the self-made water activator.

The main element of any home appliance is electrodes made from food grade stainless steel. Yes, power supply, of course.

In one version, a piece of canvas fire hose is used as the separation membrane or anolyte glass, which is inserted into a liter glass jar, which plays the role of a catholyte tank.

The mains voltage is fed through the diode bridge to the electrodes, one of which is lowered into the pouch of the tarpaulin, and the other is directly into the jar filled with water. That's the whole water activator. The scheme is simple: a liter can, with a pouch about 70 mm in diameter and 200 mm high, and electrodes up to 1 mm in dimensions about 40 × 160 mm fixed in a piece of plastic at a distance of 40 mm.

On the same piece of plastic, which should be larger than the jar of the jar, a diode bridge (diode on the anode) is installed.

Such a homemade device should not work more than 5-15 minutes. And you can not leave the resulting solutions in it, you need to pour it immediately, so that the "dead" water does not leak through the junctures in the bag in the jar.

If instead of a can and a sack take two separate containers with an even cut, and put the electrodes in each of them - into one cathode, to another anode, then, firstly, the liquids do not mix, and secondly, their volume may be the same. Only between the tanks, you need to install a connecting electrical bridge for the ions. It can be a cotton towel wrapped in gauze in several layers, tied with a thread and moistened with water. It bends in the middle, and its ends drop into the water in each jar. The process of electrolysis in such a device lasts about half an hour.

"Dead" water can be distinguished by its color - it is slightly yellowish in color.

Whichever device is invented, it is necessary to remember the safety precautions and all the actions for filling with water and draining solutions should be performed only after disconnecting the device from the network.

The initial liquid must also be prepared. At least give at least five hours of standing water to normal water. The scum from the walls of the cans should be removed, as well as with an ordinary teapot. The dishes should be clean.

Reviews about the device AP-1

The Belarusian electroactivator of water AP-1 in three modifications differs only in details, which, according to users, are not reflected in the quality of its work.

The main differences of this device are the optimal price-quality ratio and ceramic glasses. In other models, they are plastic, therefore, wear out more quickly. Even ceramics is not eternal, and those who use the device constantly, had to buy new ones. However, this is not a problem, judging by the reviews.

And further. If the influence of regular reception of "living" water on the body can be attributed to blind faith in miracles or suggestibility of a person, then stunted houseplants in full sense come to life only after a week's watering with "living" water.

These are the wonders of the electroactivator of water AP-1. Reviews about it are only positive. No, of course, you can find negative ones, but in the end it turns out that the maintenance of the device was insufficient, if at all. The instruction should be read carefully, the initial water must be properly prepared, and the cathodes and walls of the ceramic glass must be cleaned from the hardness salts in a timely manner.

Perplexity is caused only by the saturation indicator. On the fact that you need to purchase an activator model with this, almost all users converge. But there are also proposals: in order not to track the intensity of the luminescence and not to guess about the changes in the electrolytic current, instead of such an indicator it is possible to install a sensor showing the real value of the hydrogen potentials of the pH of the solutions.

Finally

The benefits of "living" and "dead" water have been spoken for several decades. And as many argue, it helps or charlatans use the credulity of the people. But those who for one reason or another have purchased an electroactivator of water, reviews about their physical condition leaves positive. They buy it first to solve their own health problems, and then they water the flowers, destroy the aphids and soak the seeds in it.