Interested in how to sew a zipper in a skirt? The answer will be found in this article

Initially, in the wardrobe of women were only dresses, tunics, chitons. For the first time, skirts appeared in the 15th century. Before that, there was a certain garment that was gathered at the throat, and its length was up to the knees. Were wearing such clothes as men, and women. The first skirts were very heavy, wide, long and of several layers of fabric. In addition, the ladies had to poddavat under them a few cotton bottoms.

Over time, the silhouette of clothing changed, and more comfortable products appeared: narrow, pencils, flares, flounces and others. All modern skirts usually have a zipper. Here she often brings her mistress. But if you know how to sew a zipper in a skirt, then you can at any time fix the clothes at home.

Skirt preparation for repair

Before you sew a zipper, you need to get rid of the old clasp. You will also need to prepare the product for work. To begin with, it is necessary to flog the old broken lightning with a blade. Usually on the seams there are threads. They need to be removed and the stitches themselves steamed. Many people are interested in sewing ordinary lightning. This is very easy to do.

Steps of sewing zippers

• Lateral sutures bend along the fold line. Usually, after stubbing, small traces of the machine stitch remain.
• From the inside on the bent side seams it will be necessary to sweep the new zipper with centimeter stitches manually. You must start from the top, not the other way around. The first stitch must be above the teeth by 0.3-0.4 mm. First, one side is taken, then the other in the same way. If you know how to sew a zipper properly, then everything can be done quickly.
• If the zipper on the skirt is on the back, then one side (usually the left one) should be seen near the denticles (the distance should not exceed 2 mm) and the other side (right) at a distance from them (about 1 cm). And if you are interested in how to sew a zipper in a skirt, if it is on the side, then it is also easy. The distance from the denticles should be the same - about 1 cm.
• Then you need to see if everything is swept correctly and there are no creases. It is important to pay attention to the fact that the ends of the lightning are at the same level. If the work done suits, then you can start to grind on the machine.
• The zipper can be sewn with a regular presser foot. Only if you perform work near the denticles, then it can slip, because of which the seam will turn out to be uneven. It is better to use a special device in this work.

Zipper sewing technology

Sometimes it seems to many that they know how to sew a zipper. But when they sit down for work, everything turns out not as we would like. In this case, just like in any other, there are some tricks.

• Begin to pritachivat need from above. After the machine needle comes to a turn, you need to raise the presser foot and turn the seam line 90 degrees.
• Then lower the presser foot and make a few stitches until the next seam.
• Again, raise the presser foot and rotate the product again upward by 90 degrees and continue the sewing.

The final stage in sewing lightning

When the clasp is stitched, you need to remove the manual stitching stitches. How to sew a zipper into a skirt is now clear. Then the lateral seams need to be ironed. If the skirt is made of woolen or other dense fabrics, then it is better to use gauze or steam iron. If the fabric is cotton or linen, then it can be ironed with a normally well-heated appliance.

Further, it remains only to pratachat back belt, if it was, or to fix the back of the obtachki.

Interested in how to sew a zipper in a skirt, if it is a secret? Here, too, has its own technological features.

• Lightning should be swept to the side seams on the front side. It is important to go straight into the fold of the fabric. After otomyvaniya you should try zip and see if everything is done at one level.
• If everything suits, then you can start pritachivaniyu. In this work, you need only use a special presser foot. The seam should be close to the denticles, otherwise there will be the impression that it is diverging.
• Then you need to zip and carefully iron the seams.

If everything is done neatly and correctly, then the zipper will not be visible when buttoned. It only remains to fix the obtachki if the skirt is without a belt. If he was, then we weld him to his former place. Now you can again wear your favorite skirt and go on business.