How to make a dress pattern according to your standards

Today, the shops are full of a variety of dresses of different styles, colors and shapes. You will be surprised to learn that most of them are sewn on a single pattern-based. This is what we are trying to master today. If the question of how to make a dress pattern will no longer cause you difficulties, then in a relatively short time you will be able to learn how to sew almost any model.

Removing measurements

Regardless of the model and style of the new dress, one procedure remains unchanged. So, before you make a dress pattern , you need to accurately remove the measurements that will be useful for sewing

Basic measures

• Half-girth of the chest. This indicator determines the size of the product. Measured at the protruding points of the chest, while it is better to wear the most comfortable underwear. The resulting number is divided in half.
• Half-girth of the waist. We measure on the most narrow place, the number on a centimeter tape again we divide in half.
• Half-girth of the hips. Measures along the protruding sections of the buttocks, taking into account the bulge of the tummy. Also, only half of the measure is taken.
• Length of back. The centimeter is applied to the protruding vertebrae from behind, just below the neck (it is easy to grope). The length to the waist line is measured.
• The width of the back. The amount between the armpits on the back, divided by two.
• Height and center of the chest. From the base of the neck to the protruding points of the chest, and between them.
• Length of the shoulder. We measure the distance from the neck at its base to the shoulder, where it begins to round off.
• The length of the sleeve. From the shoulder (the end of the previous measurement) to the wrist.
• The length of the dress. From the cervical vertebra down to the required length.

How to make a dress pattern based on the taken measurements

So, take a large sheet of paper and start modeling. The first thing to do is to apply the desired length of the dress, that is, draw a vertical line. Through its beginning and end, we carry out two perpendicular lines equal to half the chest girth (and another 3-5 cm for free fit). At the ends of each set of points and connect the opposite of them with two more vertical lines.

The result is a rectangle. In it, from above, we set aside the length of the back plus a centimeter and draw the waist line. Another half of the previous indicator is down - and you will get a line of thighs.

To build a pattern of dresses, it is necessary to lay the width of the back to the right along the length of the uppermost horizontal line, adding one and a half centimeters. From this point - a quarter of the chest girth, plus the same one and a half centimeters. From both points (we denote them, for example, A1 and A2), we again draw perpendiculars downward. Thus, the upper part of our triangle is divided into three parts - the lateral should be visually approximately the same.

In the left part we form the neck of the backrest cutout, it should not be very deep. From the edge of the cutout, down and to the right, at an angle of about 30 degrees, you need to draw a section that is longer than the length of the shoulder by 2 cm - the width of the dart. On this segment we make a dart (its length is 7 cm, the location is 4 cm from the edge of the cutout). The edge of the shoulder is connected to the point of width of the back by a rounded smooth line - we form an armhole. In the question of how to make a dress pattern, it plays an important role.

Similarly, cut out on the back, draws and a throat, but much deeper. From the edge of the cutout, this time down and to the left at the same angle, we hold the shoulder line, we have on it a chest tuck, the length to the highest point of the chest (it is on the same line with the lower part of the armhole). Finally, on the waist line from the back and from the front we draw the waist tails. To calculate their solution, add 1 cm of waist to the waist and subtract the resulting figure from the width of the dress along the waist line. It will be approximately 14 cm. The middle of the darts should be located on the waist line, up and down they narrow. The width of the darts on the waist: the front about 5, the back - about 4 cm.

In principle, the pattern is ready. On its basis, you can sew an adjacent dress-case, or you can, by adding more for freedom of clinging, to simulate a more flared version. Having basic knowledge of how to make a pattern, this will not be particularly difficult.