Large flowers of paper with your own hands

When you need large flowers from paper to decorate the room or the facade of a building, a tree or an arch, it is best to make them yourself. Master classes of making such jewelry are presented here to users.

Large bulk flowers from paper with a stapler

You can make such jewelry very quickly. Dense colored paper is required for their production. You can use whatman paper, pre-painted with colors, or colored cardboard for children's creativity. That the big flowers from a paper were more bright, it is recommended not to do an odd one. Let each petal be red and yellow, blue, and orange at once.

• First cut the lower petals, the largest.
• Then three others are prepared, of different colors and smaller ones.
• Fit the parts as the size decreases, on top should be the smallest.
• In order for such large flowers from the paper to get volume, the bottom of the entire petal stack is folded with a boat and fastened with a stapler.
• In the same way make out four more details. In total, to make a large flower of paper, five such voluminous petals will be required.
• Each detail is again fastened with a stapler underneath, grasping the side part of the adjacent petal.

Such large flowers from paper look beautiful and bright. They are used to decorate walls, create arches.

Flowers from corrugated paper without cutting petals

You can make a large flower from paper by making ordinary small buds. That is, the master folds the material around the stem with an accordion and clamps the strip down, spreading the top of the article.

To make these voluminous large flowers of paper more vivid, in the manufacture of one craft, several shades should be used. You can even combine blue and red material, purple and pink, orange and burgundy.

• In the center of the flower is placed a piece of a fuzzy wire (chenille). Bright beads are fixed at its ends. The middle of a piece of chenille is wrapped around a stem - a thick wire or a wooden skewer. It will be stamens.
• Now around the stamens lay the first layer of paper with the skirt. You can fix the workpiece by twisting the bottom with threads or a soft wire.
• The second layer of paper is stacked in the same way, only the upper edge of the strip needs to be stretched slightly along the corrugation. This will create an effect of splendor.
• So do with the third series.
• At the very end of the work, a row of green paper is used. Only the strip should be taken very narrow - it will be sepals.

Astra, cornflower, carnation

The method described above is an example of making a fantasy flower. However, in almost the same way do asters, carnations, cornflowers. The difference lies in the fact that before working a strip of corrugated paper must be prepared.

It is necessary to make one its edge notched, using special scissors or cutting out triangles by hand. You can make transverse cuts on the strip to the middle.

Flower-bow

You can use a stylized imitation of flowers to decorate. Such a large flower made of paper is made from loops made of colored strips.

The petal is simple enough. A segment of a wide band bends in half across, but the folding point does not need to be ironed. Is not it true, the petal reminds half of a bow from a tape?

Both ends of the strip are in one place. They are compressed and laid around the stem. Having collected the necessary quantity of petals, the master fixes them with threads or wire at the bottom.

Sepals are manufactured in the same way as in the above-described embodiment.

Dahlia made of paper

According to the algorithm of making a flower-bow, you can build an imitation dahlia. For this, at the time of folding across the paper strips are made in the bottom of the incision. They should be equal somewhere about three-fourths of the length of the folded loop and do not reach the cut so that the petal does not disintegrate. The rest of the work is done according to the scheme described in the previous section

Corrugated paper rose

The queen of a flower garden has always been considered a beautiful rose. This is one of the most difficult in the execution of the craft. In order to make flowers from paper (large or small - not important), resembling a rose, you will need to cut out each petal and work on it.

• So, prepare the right amount of details in the form of a heart with a slightly flattened top - do not sharpen it, let it be better to have a concave arc.
• Each petal should be slightly stretched in the middle, giving it a convex shape.
• The upper parts protruding above the concave arc are wound on a pencil - they are twisted.
• The inner bud is usually not exposed to roses. Therefore, the first petals should be turned inside. Having combined them with your hands, you can get an undisclosed inner bud. In the same way, it is recommended to lay a couple more petals.
• The next row is made of parts spun outward. To a large volumetric flower of paper turned out to be as much like the real one, it will take quite a few such petals. Than there will be more, the more magnificent and attractive will be a rose.
• From below the flower has sepals. Wind the stem with green tape. In the absence of such a roll of green corrugated paper can be cut across, so that a thin roll about a centimeter wide is obtained. Having pasted its end to the stem under the flower, the craft itself is taken to the left hand and is lightly twisted clockwise. The thumb of the right hand is pressed and pulled lightly with a strip of green paper. Each turn goes down a little in a spiral. Thus, the whole stem is wound up.
• You can insert a green leaf during wrapping - this will give a great similarity to a rose with a real living flower.

Rose "wasteless"

You can simplify the work of making a queen of flowers. This method excludes cutting each lobe separately. It is enough to make cross cuts equal to the width of the petal on a wide strip of corrugated paper. Each straight corner of the rectangle from the strip is wound in a known way on a pencil. The first four petals are turned inward, the rest are outward.

Then you should stretch the petals in the middle - each separately. Put everything on the prepared strip around the stem, straightening the petals and squeezing the strip from the bottom of the accordion, giving the product the necessary volume.

Further design of the craft is made in accordance with the algorithm described above.

Poppy from pleated petals

This flower is easy enough. To make it, you need to cut out petals that are in the form of droplets from a color that is sufficiently thick. It will take only eight such details. The petals are folded along the accordion, then straightened.

On a small green circle - sepals - glue the workpieces, slightly attaching the bottom part, so that they rise above the plane. The first row consists of five parts, and the second one consists of three parts. And the inner layer must rise above the outer layer.

For the middle of the flower, you need to cut two circles: the yellow should be slightly larger than the black one. Along the circumference, the details of the yellow color make many cuts to make the stamens of centimeter width. They are curled with scissors (ironing with force) or with a pencil. Seredinku glued alternately: first a yellow part, and on top of a black one.

Briefly about the main

To the flowers turned out beautiful and lush, the master will need the accuracy and desire. Bright materials will also do their thing. And the master classes published here will help beginners to perform the presented models.