How to make a bracelet from a rope: a master class, step by step instructions and recommendations

Such a stylish accessory, like a bracelet, can be easily done by yourself, using only improvised tools. Consider the different types of these ornaments, the basis of which is the rope.

Simple bracelet made of twine

The usual twine, woven and put on the arm, can look very impressive. And to make such a bracelet from a rope is simple. It will take some time.

You can use, for example, the macrame method. To do this, take two pieces of not the most coarse twine length of about five meters, fold in half and fix the bend. It can be fastened with a pin, tape, press a book and so on. Then weave will become much easier.

The threads are separated and knots made from external twines by tying the central ones. And so repeat, each time throwing them over the central ones. While tightening the knots, you should pay attention to the central threads can not be seen.

Bracelet made of twine with beads

How else to weave a bracelet out of a rope? Very nice looking decoration with beads. For him, take seven threads, the length of which is one and a half meters. Six pieces are collected and looped. And the seventh thread is tied with a loop on the side. Further, this thread binds the entire loop of six threads. At the end it is cut off and hidden.

Then, six beads are strung on beads of different sizes. In this case, the largest of them should be located far apart from each other. After this, make a knot and again string the different beads. Again a knot and so on. At the end thread one large bead, which will act as a fastener. One more accessory is ready.

Rope bracelet with decorative ring

An interesting option may be a wicker accessory. As the main material is better to choose a bright thread of cotton, and an element of the decor will make a metal ring. From the consumables you will need glue and fasteners.

Take three strands, fold them twice, forming a loop. This part will become a knot for the metal ring. To do this, a ring is threaded onto one end of the rope, and the other end is passed through the loop and tightened. A similar knot is made on the other side of the ring. It should turn out a ring in the middle, with six threads stretching on each side of it.

Next, weave a pigtail with one, and then on the other side. Having received a length sufficient for the bracelet, the excess ropes cut off, cauterize the ends, spread them with glue and insert the prepared fasteners. It remains to add a clasp - and a fashionable bracelet from the rope is ready.

Bracelet from a large rope

For this bracelet, take ropes, whose diameter is 5 millimeters, metal clasp and pliers. How to make a bracelet from a rope?

One rope is folded in half and forms a loop. Another rope is also folded and placed under the first loop. Then take a loop of the second rope, place it on the first loop and stretch it under the ends. The formed loop is laid on the beginning of the second rope, passing it under its ends. The resulting knot should be tightened evenly on both sides. From each side there must be hinges and rope tips.

Try on the future bracelet, you need to cut off the big ends, set them on with a cigarette lighter and fasten them with clasps on both sides. That's all. Strikingly light, but very stylish bracelet from the rope is ready.

About the bracelet "Shambhala"

This magic, as the supporters of religion assure, the bracelet is a unique source of energy. The effect is achieved by weaving two cords, inside which weave different beads. Those who want to learn how to weave bracelets from the ropes of "Shambhala" will need the following materials:

• board;
• Cords waxed 3 meters long;
• glue;
• 10-15 beads;
• scissors;
• lighter.

Beads are better to pick different types. They can be both wooden and metal, from natural materials and precious stones. Also, the beads are selected from monochrome, variegated and of different colors. Even the form is different. And if round beads are selected, they symbolize peace of mind, tranquility and happiness. Cherepobraznaya form will protect from dangers, snakes will reveal the potential for dramatic changes in man, and beads-crosses will bring stability in life.

The cord is chosen in most cases from a synthetic rope. Suitable nylon or nylon, the diameter of which is almost two millimeters.

How to weave bracelets from ropes "Shambhala"

Having prepared everything you need, you can start to weave. To do this, take a tablet and nail to it two nails, one opposite the other. On the one hand, tie one end of the main rope, to which beads are strung. The other end is tied to the second carnation. The thread must be stretched.

The second thread is doubled and tied up above the first bead. The left part of it is passed under the main rope, and from above it is put on the right rope, which is passed over the main rope and makes a loop, tightening it. The same manipulations are alternately done with one or the other. After 20 or more nodes have the first bead. Each of them is decomposed in an arbitrary order, but the basic scheme can be chosen as follows: 22 knots, a bead, 9 knots, another bead, and then three beads and beads are placed three times through the same number of knots. At the end, as in the beginning, make 22 knots.

After finishing the weaving, the bracelet is removed from the studs, a few additional knots are knotted in addition and the threads are cut off, having blurred the tips of the superglue. But the main rope is not cut.

Fashionable and expressive bracelets

Bracelets made of ropes with their own hands can be made very expressive. Take any bright rope, measure the diameter of the wrist and cut into five pieces, cauterize and fasten on one side with a clasp. Next, take a thread mulina one color range and braid all the pieces of the rope, moving perpendicular to their location. At the end of the work, the ropes are fixed on the other side.

Another simple way how to make a bracelet out of rope is the following. Take a bright rope forty centimeters in length, a clasp with a crimp and a large wooden bead. The rope is cut into two pieces and fixed one side together with the floss of the moulinne. Then we twist both threads in such a way that they like, in the middle string the bead, add them to the end and fasten the fastener on the other side.