How to install a mount on a snowboard? Mounting the mount on a snowboard for a beginner

Fans of winter sports, who have already chosen a board to conquer mountain peaks, must be guided in how to properly mount the mount on a snowboard. The presence of such knowledge will allow you to adjust the board, based on personal preferences and the chosen style of riding.

Structure of fastenings on a snowboard

The standard mounting for snowboarding includes the following set of elements:

• Base;
• Highback;
• Gas pedals;
• Upper and lower straps;
• Disks.

Since the clips of the fastenings always look outwards, in practice it is quite easy to distinguish between the left and right snowboard mounts. It is enough to look at the disc on which there are notations in degrees from 0 in both directions. The presence of additional holes in the disk is due to the need to adjust the fasteners in the front and the opposite direction.

How to install a mount on a snowboard, based on the rack?

When attaching the fasteners, it is important which foot prefers to stand on the rider's board during the movement. It is rather difficult for novice snowboarders to immediately choose the right rack. Basically, everything is learned in practice.

However, there is still an effective way to determine the most convenient rack in the home. To do this, you need to get a small push in the back. Which leg will move forward first, that, most likely, is the leader when riding a snowboard. To make sure of the result, it is worth repeating the experience several times.

If the right leg was in front, in this case it is necessary to mount the mount on the snowboard intended for this foot, closer to the bow of the board. Based on the nature of the location of the anchorage, the width of the post will be adjusted in the following. One rider is comfortable with a wide rack, the other - narrow. Beginning snowboarders are advised to set a rack of medium width.

Adjustment of fasteners

Before proceeding directly to the installation of the fixtures, it is necessary to try them on together with the shoes. This is required for tuning the gas pedal. This element is adjusted from the side of the base. To understand this issue, it is necessary to put the boot in the fastener, fastening the lower and upper straps. Then the gas pedal should be set in such a position that it reaches the bend of the toe on the sole.

How to install a mount on a snowboard? It is necessary to center the stapes. For this, there are special means for adjusting from the back of the clip. In addition, you need to pay attention to the fact that the highback tightly resorted to the boot.

How to mount a mount on a snowboard with a high level of rigidity?

If there is a hard board with the appropriate type of shoes, in this case it is better to install the fasteners according to the so-called carving stand, which makes it possible to make sharp, sharp turns at high-speed distances.

The angles of placement of fastenings on rigid snowboards are determined by the width of the board. First you need to install the rear mount so that the socks look a little at the board. At the same time, the heels should be located clearly above the back edge. This will allow maximum pressure on the edges of the board.

The installation of the front attachment should be performed on the angle of the rear attachment, adding to its position about 8 ^° . In the future, it will be possible to adjust the angles for comfortable skating, based on individual wishes.

Installation of fasteners on standard boards with soft boots

How to properly mount the mount on a standard model snowboard ? You should try it out by starting with setting the standard settings for these types of boards, which assume the adjustment of the fastenings at angles of + 21 ° / + 6 °. When determining the most convenient rack in practice, it will be possible to slightly change the setting of the angles of the order of 3-4 ^o in the required direction.

Rack alignment

To understand how to properly mount the mount on a snowboard, you need to understand the issue of centering the rack. This is required for the alignment of the feet with respect to the width of the snowboard, which helps stabilize the turns while driving.

The best way to center the rack is to shoe boots with attachments, and then try to feel where the foot should be in relation to the mounting discs. In this case, attaching the mount to a snowboard for a beginner can be somewhat difficult, since some fasteners have a fixed heel. In other models of fastenings the heel can move in both directions, which contributes to a more convenient change in the position of the shoe.

Width of rack

Under the rack width option, the distance between the center points of the individual fixtures is to be understood. To understand how to properly mount the mount on a snowboard, in this case, you need to build on the parameters of your own growth.

The width of the rack should be exactly equal to the distance from the ground to the middle of the rider's kneecap or be 2.5 cm larger than its width of shoulders. The width of the rack has a profound effect on the ability to control the behavior of the board. The widest stance gives stability to movement, but complicates the change of the edge. The reverse effect is felt when the indicator of the rack width decreases.

It's important for freestylers to understand how to properly mount a mount on a snowboard, based on the width of the rack, which often deliberately increases this figure to perform complex tricks. While fans of speed descents often prefer narrow racks.

It is recommended to beginners to use a natural rack, resorting to the default settings specified above. The independent change of this parameter seems appropriate only for experienced snowboarders, who are able to distinguish the effect from the adjustment of individual settings in practice.