How to fix a faucet in the kitchen? A tap is running in the kitchen

If it happened that the tap is leaking, then often many people turn to management companies and invite qualified plumbing. But not always these specialists can wait on time. So, what if there is a tap in the kitchen? How to fix it with your own hands and what tools are needed for this, any home master should know.

Preparatory work

The very first and most important rule for all repair works for plumbing is the disconnection of the water supply. Often, the valves that are responsible for it can be found in the toilet. In order to turn off the flow, simply turn the tap.

However, due to the fact that there were no problems with the equipment and these cranes were not used for a long time, the valves can become rusty or blocked. These valves should be developed with the utmost care and very smoothly. Gradually, you can increase the effort, also do not forget about the lubrication. This is the first thing to do before fixing the current tap in the kitchen, in the bathroom and in any other room.

Required Tools

Before work it is important to collect the necessary set of tools. They should be at hand at any time.

So, for work you need a swivel wrench, a flathead screwdriver and a crosshead, wrenches. Often, this modest set should be enough. It happens that suddenly and strongly flowing tap in the kitchen. How to fix, what keys it is necessary - here it is impossible to say specifically. The fact is that each manufacturer has its own standards. There will be enough of a set of keys that every motorist has.

Also, it is not superfluous to prepare various additional elements. These can be pieces of rubber, leather, from which you can make gaskets. It can also come in handy fluoroplastic sealant in the form of tape, rags, detergents.

Sometimes in the process of repair, keys or any other tools may fall - so as not to damage the expensive washing or sink in this way, put a sponge, a rag, or something else that can absorb shock.

Why there is a tap in the kitchen: how to fix and type faults

Flowing cranes are quite common. But there are not so many reasons that can cause a breakdown. There are four most common ones.

Poor quality of the cranes

Often buying plumbing fixtures, many people are guided by considerations of economy and choose products of Chinese or Turkish production. At the same time, people are happy that they were able to save this way.

But this tactic when buying mixers is extremely erroneous, and the joy of the saved amount does not last long. This small amount can cause leakage. Well, if at the moment when the crane breaks down, someone will be at home and will soon be able to cut off water or repair equipment. But more often it is different.

You should never save on things like plumbing fixtures. Be sure to make sure before purchasing that the offered goods are not made in China, but at least in Russia or in Europe. Also, cheap products for a well-known brand - this is the reason for suspicion. Expensive brand products in our markets are 50% fake.

Sometimes it happens that even on expensive equipment something can leak. Then it is worthwhile to get acquainted with other reasons to understand how to fix a faucet in the kitchen. Flow also in the case of illiterate erection.

Wrong installation

Here you can also safely turn on production defects or errors in the assembly of the product. If you buy a high-quality mixer, for a serious price, it is necessary to take responsibility for its installation with all responsibility. Various errors that could happen during the installation process can minimize all the advantages of an expensive product.

Violation of operating rules

This is another popular reason. It is very important to remember that the crane, like many other devices and devices, has performance characteristics. If excessive force was applied during use and pressure was applied to the parts of the valve, then do not think that for the device it all went without a trace.

Natural wear of parts

In the course of frequent use cycles, various moving parts of the product can be worn. Especially often, rubber seals and various gaskets come into disrepair. In this case, there is nothing easier than to fix the faucet in the kitchen. Flowing? It is enough to replace the gaskets.

The problem with gaskets is more relevant for traditional models with two valves. In the case of ball valves, the device of which is seriously different, you will need another repair scheme.

Crane repair with two valves: replacement of gaskets

How to fix the current tap in the kitchen, if it flows constantly, no matter how tightly twist it - it's all in the worn out gasket. It must be replaced. The first thing to do is unscrew the valve body - for this, it must be rotated clockwise. Then remove the damaged seal. If a new gasket is not available, it can be made of rubber or leather. As a sample, it is recommended to use the extracted part. Then a new gasket is put in place of the old one. The sealant is wound on the stop edge, the valve body is mounted to its rightful place.

For reliability it is necessary to tighten the valve a little with the help of spanners. In order not to waste time on the process of manufacturing the seal, it is easier and quicker to purchase one in the store or on the market.

We replace the sealing liner on the stuffing box

During use, wear of this liner can trigger leaks. What to do in this case? How to fix a faucet in the kitchen? It flows most often at the moment when the element is open. Water passes between the nut on the stuffing box and the stem on the valve.

With a screwdriver, unscrew the nut on the stuffing box. Further, a liner is made of PTFE tape. Then it is put in place of the worn out, and the nut is twisted.

If it flows from a spout

Often, a tap flows in the kitchen. How to fix it? Very, very simple. To do this, unscrew the outer nut. Then very gently the spout rotates and rises, and then it is removed. It is necessary to carefully check the insulating gasket and the expansion ring. If something is worn out, a replacement can solve the problem.

We repair the ball in the kitchen

Fashionable and modern faucets have a more sophisticated device, unlike valve models. How to fix a faucet in the kitchen? A ball valve flows - it means that any contamination has got into it, which prevents the mixer from working normally.

So, to defeat this problem, the crane is dismantled and cleaned. The first thing to do is to screw out the locking screw of the lever. Then very carefully remove the lever. Using a screwdriver, unscrew the screw, remove the dome and the sealant from the plastic.

The latter should be carefully inspected, and all the plaque removed on it. If it is worn out, it is recommended to purchase a new part. Then remove and carefully inspect the ball - if there is damage, a replacement is necessary. When there is a wear of the seals that fix this ball, they are also recommended to be replaced immediately. Then, after replacing parts or cleaning them, all plastic elements must be lubricated with the composition recommended by the manufacturer. Sometimes it happens that even after replacing parts the tap in the kitchen still flows. How to fix it? The repair scheme will be slightly different - here it is necessary to replace the entire cartridge of the crane.

A new tap is running: what to do?

Sometimes there are such situations. The reason for this phenomenon is industrial marriage. Inside the crane there may be various defects, such as fragments or cracks. With their own hands they can not be eliminated. You need to change the product from the seller. Now you know how to fix a faucet in the kitchen. Is the water flowing? This is no longer a problem.