Energy (floor heating): manual, reviews, manufacturer

Today, when there is no hope for central heating, increasingly modern consumers prefer to install a system of warm floors. They are presented to the attention of buyers in a wide range, manufacturers tirelessly offer users different models that have unique characteristics. As one of the options you can consider the products of the manufacturer Energy, the warm floor of this company is offered in several models, which will be discussed below.

About the manufacturer and products

Energy - warm floor, instructions, the regulator of which is presented in the delivery set. Specificity of the described products is that domestic materials are equipped with heating elements of foreign production. Thus, the cable in the models is manufactured by the English company Lytellton Limited, which attracts customers. At the heart of the mats is a polymeric heat-resistant material, which is characterized by high mechanical strength and insignificant thermal conductivity. Today the company offers several systems that differ in the scope of use.

If the room has basic heating, then the problem of insufficient intensity can be solved by using thin mats or single-core cables that are mounted on the tape. There are also powerful heating cables that are installed in rooms without additional heating appliances. The optimal solution is the model with a two-wire cable of impressive cross-section. It can be about mats or sets of heating elements. Among other things, you can choose floor heating systems on the street, for example, in outdoor areas and terraces.

Opinions about the Energy Mat system

If you are interested in Energy products, you can purchase the warm floor of this manufacturer in the Energy Mat variant, which is used as an additional heating system. According to buyers, these are mats, which are equipped with heating two-wire cables. This warm floor is a thin substrate, on which elements with a diameter ranging from 2.8 to 3.5 mm are installed. Users emphasize the main advantages of use, which are expressed in the simplicity of styling and extensive choice of models. Quite often Energy Mat becomes a part of the floor, on which ceramic tiles are subsequently laid.

Comments about underfloor heating brand Energy Light

Often, modern consumers are interested in the products of Energy. The warm floor of this supplier is also available for sale in the Energy Light version, which is a single-core cable used for a small increase in temperature. Structurally, these models do not differ from the Mat version, in this case heating elements are also installed on the polymer substrate. The core diameter is 2.8 mm, while the specific power is 100 W / m².

As the buyers emphasize, the cables are a multi-layered construction, and the thermocouples are protected by polymer composition. From the words of buyers it can be understood that the design is reliably protected from mechanical damage by the casing, which is made of PTFE. Users choose this model also for the reason that it has an affordable cost. But you can install these heating mats in any location, such as living rooms, toilets, bathrooms or kitchens.

Installation Instructions

Energy - a warm floor, which is quite easy to install. However, before carrying out these manipulations, it is necessary to read the instructions. First you need to determine and prepare a place for the temperature controller and temperature sensor. For this, space is chosen on the wall. The thermostat should be located at a height of 1.5 m from the floor. It must be installed within the mounting area of the mat. This approach will simplify the withdrawal and placement of the tube with a temperature sensor. At the selected location, an electrical installation box is installed, to which 220 V power is supplied.

Nuances of works

In order to make the connection as convenient as possible, the ends of the wires must be taken out of the box for 10 cm. Energy - a warm floor, the installation of which can be carried out by any domestic master. At the next stage, the technology involves making grooves, the width and depth of which should be 2 cm. It will house a corrugated tube with a temperature sensor. Strobu should be routed from the thermostat to the center of the heating mat. The bending of the tube is permissible only in the place where the element passes from floor to wall. If the work is done in a humid room, the thermostat should be located in the next room.

Recommendations of a specialist

The next step is to prepare the floor surface to lay the heating mat. It should be located on a dense and level surface with sufficient load-bearing capacity. If the base is deformed, this can lead to cracks in the tile adhesive layer. When a heat-insulating layer is used, it is necessary to lay a concrete screed 3 cm thick on it. Only after this the heating mat is laid.

Energy - a warm floor, the instruction for laying which you should be studied, is a system mounted on a specific technology. In the next stage, it provides for the implementation on the floor surface of the grooves for laying the cable joints . The surface of the floor is cleaned in the installation area, where it is necessary to remove debris and sharp objects. When working with a temperature sensor, the mechanical action on the encapsulation of the sensor should be avoided. This may damage the thermosensitive element, which will require replacement.

The temperature sensor should be located inside the corrugated tube, while the sensor itself will be in the floor, and its connecting cable will exit from the other end of the tube, which will allow connecting the thermostat. Energy - a warm floor, the feedback about which is often only positive, should be sealed at the end of the tube with the sensor. Otherwise, water or an adhesive solution may enter inside, which will require the replacement of the temperature sensor. The tube is placed in the prepared rod, and after it must be taken to the location of the thermostat. To ensure the possibility of replacing the sensor, the end of the tube should be put into the electrical box by 2 cm. It is important to make sure that the bend radius is not less than 5 cm.

For reference

Stroba filled with glue, and the location of the sensor is noted. The laying area should be primed using a deep penetration composition. If you are dealing with a highly absorbent surface, then it must be covered with a primer in 2 layers. Before installing the heating mat, allow the surface to dry out.

Conclusion

Energy - a warm floor, the manufacturer of which took care of quality. However, you must follow all installation rules. Thus, the heating mat is laid on the heated area, and then work is carried out on pouring the surface. In this case, the master should wear shoes with soft soles.