Drovnitsa with their own hands (projects). Drovnitsa with own hands in the country

Drovnitsa own can be made with ease, but before that you need to decide on the amount of fuel you expect to put in it. Only with the use of high-quality dried fuel can you get a good steam in the bath and the heat that radiates the structure for heating the room. In addition, only with dry wood you can cook shish kebab according to the rules. If you do not wish to fill up the shed with firewood any more, since there is not enough free space in it, you can independently make a drovnitsu. It is important to find a place for it so that there is an opportunity to guarantee fire safety. Thus, the drifter must be located not so close to the residential building.

Selecting a size

Drovnitsa, made by hand, can have different sizes. The one that has large dimensions, can be located on the street, and the one that will be used every day, can be located in immediate access from the stove or fireplace. This eliminates the need to go out for firewood every time you need to undermine the hearth. The described special place for storage of small portions of logs must also comply with the fire safety rules, which indicates the need to give the structure the ability to ventilate. But as for the external drovnitsy, it must be done so that it has a canopy, because the fuel should not get water.

Varieties of driftwood

If a drifter is made by hand, then it is necessary to adhere to certain recommendations on design parameters. Thus, if you want to get a dower for temporary storage of fuel, then its capacity should be in the range of 0.5 to 1.5 m ² , this is enough for a bath. Whereas if it is supposed to make a drovnitsu for cooking shish kebabs and other dishes, then this indicator may be somewhat smaller, it can be limited to 0.2-0.4 m ² . Drovnitsa, made by hand, can also be portable, so that it would be convenient to bring it to the barbecue grill. Its capacity can be 0.3 m ² .

Features drovnits

If you need to use a place to store fuel when firing a fireplace or a stove, wood or metal can be used as material for making. Less often, such drovnitsy from willow rods are performed , but they look very original and harmonious. The insignificant weight of the product is the main feature of the portable fuel storage, in addition, the structure should have an impressive capacity, but do not fret with the last quality, because you can get an installation that will take up too much space and use it as a portable capacity will be Uncomfortable.

Drovnitsa with their own hands at the dacha should be made in such a way that the bottom was continuous, this will prevent the loss of debris and all sorts of wooden remains. If you make a portable drovnitsa, then it must be done with handles. Making a place to store firewood, which is intended to be used only in the house, wheels can be attached to the bottom.

Preparation of necessary materials

Drovnitsa for the fireplace with their own hands can be made independently, if it is possible to prepare some materials and tools, among them it is necessary to distinguish:

• Wooden bars, which will form the basis of the skeleton of the product. The cross-section of these elements should be equal to 50 x 50 mm.
• Tes for the manufacture of a roof lath system.
• Flooring boards.
• Slate sheets, which can be replaced with another covering material.
• Nails designed for slate work.

The amount of construction material will depend on the dimensions of the structure. If the drovnitsa is installed on the street, then it is necessary to protect and its side walls, for this you should use a corrugated sheet. However, it is also possible to sew the side walls with a strap.

The technology of making drovnitsy

Drovnitsa own hands at the cottage should be installed using a special technology, the features of which will be described below. Once you can select a location for installation, you need to prepare four pits, each of which will be mounted post. Depending on what capacity the drovnitsa will possess, it is necessary to determine the distance between the supports. Conditionally, we can assume that the length of the storage space should be about 3 meters, while the width should not exceed 1.5 meters. In the role of supports it is necessary to use a paired bar, the cross-section of which is 50 x 50 mm. It is necessary to deepen the pits by 40 or 50 cm.

Front and rear supports must have different lengths. This indicates that the lengths of the beam, which will be located behind and in front, should have a length equal to 2 and 2.3 m, respectively. At the next stage they must be installed in ready pit, and then covered with stones with clay. Each of the materials is poured separately so that it is possible to produce a rammer. It is necessary to protect the covered part of supports with a special material, which can be used as an adhesive tape or roofing material. This will ensure a higher degree of moisture-proof construction.

Mounting the strapping

Strapping mounted poles must be done using a bar, you need to do this on three levels. The bars, which should be located in the lower part, should be strengthened in steps of 10-15 cm from the construction site. As for the next bar, it must be fixed to the central part of the supports located at the rear. After that, you can go on to make the upper screed, which is mounted on the rear and front posts on their upper ends.

Side supports should be fixed to each other by means of a bar on three levels. A stronger and more stable construction will become if the braces to its rear and side rails are strengthened.

Roofing

Before you make a drovnitsu with your own hands, you need to think whether it will have a skeleton skeleton. In favor of this, it can be said that this design will protect wood from rain. In view of the fact that the pillars have different lengths, the master will have the opportunity to equip a pitched roof. You can take other sizes of poles, but in the example a difference of 30 cm is used. If you provide a slope, this will guarantee the moisture drain.

When a douche-wood is made by oneself, projects must be prepared in advance. They can be seen in the article. At the next stage of the work, you can proceed with the laying of the crate, which is mounted on the upper screeds. If there is a desire, then the insulating material can be laid on the roof . As a covering material, slate can be used.

Recommendations for manufacturing

When a street drifter is made by one's own hands, lags should be laid on the floor under the boards, the step between them should be equal to 1 m. This will allow additional ventilation of the driftwood. If the design is installed on a solid surface, then this method should be discarded. The wall covering should not be made deaf, but leave grooves for better ventilation. This is how the drovnitsa is made for the fireplace with their own hands. Projects of this design can be seen in the article, it can easily be performed independently.