Do not squeeze the washing machine: causes, problem solving and recommendations

A modern washing machine is an indispensable assistant in every home. It is considered to be one of the most effective types of household appliances. The washing machine perfectly copes with the function assigned to it. For a short time she will turn the dirty laundry into a clean one. Thanks to the squeezing function, the washed clothes are taken out by the consumer from the drum in a semi-dry condition. But sometimes the working capacity of the device is disrupted, and this function stops working. Why does not the washing machine squeeze out? The causes of the malfunction may be different. Depending on the degree of breakdown, they can be eliminated either independently or with the help of a master.

How to understand that the spin does not work?

It is not difficult to do this. As a rule, after the end of the program, the laundry in the drum turns out to be semi-dry. If the washing is completed immediately after rinsing, the laundry remains very wet, and water can drip from it.

Also, the remaining water in the drum after removing the laundry indicates the spin failure.

These two indicators indicate that after washing, the washing machine does not spin. The reasons for such a malfunction and the methods of their detection are different. For a start, you can try to figure out the problem yourself.

The washing machine does not squeeze the laundry properly: causes

Often, the failure of parts is completely absent. Even if the washing machine does not spin. The reasons lie in the improper use of the device. By ignorance, some owners believe that this is due to a malfunction.

Incorrectly selected washing program

Not all programs provide a spin cycle. Therefore, after rinsing, the washing machine simply drains the water and finishes the operation. On many models, this function is not provided for the "Delicate Wash" program.

To ensure that your device is functioning properly, it is worth looking into its instruction manual and studying the information about the cycles provided for in this or that washing program.

Overload of the drum with linen

This is the most common problem in narrow models up to 40 cm. The fact is that at high speeds in an overcrowded tank there is an imbalance, and the control module makes a decision about the end of washing. Therefore, if the washing machine "Indesit" does not squeeze, the reasons are most likely in overloading the tank or knocking the laundry in one lump. Why this company? Because it is quite popular with its narrow models at 33-35 cm wide.

Uneven distribution of laundry in the drum

This problem is also primarily a narrow washing machines or models without controlling the imbalance. This function is responsible for the uniform distribution of laundry on the walls of the drum before proceeding to the "Spin" cycle. It is carried out due to reversible movements. If the laundry in the drum is unevenly distributed, the spinning will start at a low speed or the washing program will be stopped altogether. As a result of the presence of unbalance control during spinning, vibration and noise are reduced, thereby prolonging the service life of household appliances.

But if the matter is not in the program and the loading was performed in accordance with the allowed norm, and the washing machine stopped wringing, the cause may be in the failure of any component parts.

Drain pump malfunction

In this case, the spin function itself will work correctly. It's just that the machine will not be able to drain the water, it will remain in the drum and will not go into the sewer. In this case, the electronic module will not be able to start the rinse cycle at the correct speed. To restore the efficiency of the device, it is necessary to replace the inoperative drain pump.

Malfunction of the pressure switch

This is the device that transmits the signal to the electronic module about the water level in the drum. And if in the washing process the "brain" of the washing machine does not receive the necessary signals from it, the spin function is not activated and the laundry remains too moist. If the wizard determines that the problem is in the pressure switch, it will replace it with a new one.

Faulty electronic module

This is one of the undesirable and most expensive failures. If the "brain" of the device came out of the standing position, not only the spin function can work incorrectly. According to the master, this is the most common reason when washing machine LG does not wring. The reasons lie in the electronic module. Modern models of these devices have complex control, which is very sensitive to overvoltages in the power grid.

In order to restore the efficiency of the washing machine, it is necessary to contact a qualified technician, he will either replace the board or reboot the module itself.

It should be noted that the command vehicle very often fails due to power surges. Therefore, in order to secure their home appliances, it is worthwhile to connect it through special protective shutdown devices or a difa-automat.

Malfunction of the electric motor

According to the master, if the washing machine "Burning" does not squeeze, the reasons are often in the motor. A malfunction of the motor may occur due to breakage of the winding or wear of the graphite brushes. In this regard, the engine loses its power and it is not enough for a large number of revolutions, which is provided in the spin function. Often this cycle of the program is turned on, but the drum is not enough to accelerate, so the laundry is not squeezed properly.

With this problem, only a qualified master or a person with experience in working with similar devices can understand this problem. Restore the efficiency of the washing machine will help a partial repair of the electric motor or its complete replacement.

Malfunction of the device

This device is responsible for the number of revolutions of the drum per minute during washing. If the washing machine does not spin, the causes in the tachodchik are quite rare. But if the wizard fixes a malfunction of this device, it will replace it with a new device.

What should I do if the spinning in the washing machine stops working?

If during the execution of the program the machine did not perform the last cycle, you must:

1. Check the laundry in the drum, maybe it got stuck in a lump. For this reason, the electronic module stopped execution of the program. Often this happens when washing bed linen, when everything is collected in a quilt or pillowcase and the machine can not evenly distribute the contents. It is necessary to get the laundry from the drum, load it separately and activate the function "Spin + Rinse" or "Spin".
2. Check the program explanation in the instructions. Perhaps it just does not provide this mode. In this case, the spinning can also be started separately.
3. Exclude the overload of the drum. Especially sensitive models with electronic control are sensitive to this. In case of overload, they simply stop the washing process in any mode.
4. You can try to start the program again, maybe the program crashed.

In all other cases, you will have to contact the service center for the help of a qualified technician. Since it is difficult to understand which particular component has failed, it is quite difficult for a person without experience. In addition, special equipment is needed for this.