Diamond Drilling: Technology and Key Benefits

Every year, diamond drilling and drilling of concrete supplant other technologies. For example, a puncher has many disadvantages, in contrast to this method. This vibration, high noise , etc. Most often, this drilling is used during construction or repair work. Let's talk on this topic and see what are the pros and cons of diamond drilling.

Diamond drilling: general provisions

The main difference is that when using this technology there are no shock loads, as well as excessive vibration and noise. To achieve high results, modern technologies (diamond drill, special equipment with noise suppression) are used. During the construction of a building, it is often required to make a deep hole in the concrete. If you use a jackhammer, it is very easy to damage the structure, and this is fraught with consequences. Diamond drilling and drilling are characterized by high productivity, which allows you to perform large amounts of work. But this is not all the advantages that I would like to say. Let's talk about the pros, which in this technology a lot.

Diamond hole drilling: advantages

One of the main advantages is that the customer can get the most accurate hole sizes. This is very important, especially when performing assembly works of a high level of complexity. The absence of dust is another rather important factor. Sometimes hydraulic suppression is used, that is, ordinary water. As already noted above, the unstressed method of drilling allows to achieve almost complete absence of noise. Processed metal and concrete structures do not undergo dynamic disruptive loads, which extends the service life. Sometimes with the help of the same perforator or jackhammer it is almost impossible to make a hole for communication (power supply, water supply) in the building, and to install diamond drilling it is not at all a problem. Moreover, the hole will be perfectly smooth and smooth, which is undoubtedly important.

About technology

Diamond drilling of concrete is a complex process, during which expensive technology is used, so this technology is considered to be unique in its own way. It consists in the following. At the first stage, the marking of future holes is made. At this time, their depth and diameter, as well as the angle of inclination, are determined. Next is the drilling process itself, which lasts only 10-20 minutes, depending on the conditions in which work is performed, and the dimensions of the hole. Thanks to the built-in cooling system, the installation does not overheat, which makes the work uninterrupted and performs everything in one approach. Once again, you should pay attention to the fact that the diamond crown is a high-strength product, so they can drill a hole in any metal structure.

On the technique used

The process is simple enough, but it involves the use of special expensive equipment. In most cases, this is a diamond crown and a special drilling rig. The device of the machine is quite simple. This includes a hydraulic drilling device. As you know, the use of a cylinder with a fluid, that is, hydraulics, allows you to achieve maximum accuracy and smoothness of obtaining holes. Sometimes an electric motor is used. If it is a question of repair of asphalt, then two-stroke internal combustion engines (ICE) are most often used. When electric installations for drilling are used, both single-phase plants and three-phase plants are selected. The former are more preferable from a technical point of view, therefore they are used more often. Typically, the units are equipped with an air cooling system, their power is about 3 kilowatts. As for the three-phase plants, they are also used, but they have large dimensions and operate from the 380V network, which is only available at construction sites.

Conclusion

Today, most often this technology for obtaining high-quality, accurate and smooth holes is used to install split systems. It is also possible to get holes under the anchor of almost any size in any foundation. A high-quality drill of diamond drilling allows obtaining holes with a diameter of more than 200 millimeters. The price of such equipment can be about 100 000 rubles. It should be noted that the hole obtained does not require further processing, that is, grinding, adjusting, etc. All this is saving not only the means, but also the time, as well as the forces of both the customer and the performer. Such drilling rigs operate in both open and closed rooms. Practically complete absence of noise makes it possible to use drilling in residential houses during repairs or renovations. Here, in principle, and everything that can be briefly told about this method of obtaining cylindrical holes of different depth and diameter. Certainly, the high cost pays off by quality, and this is an indisputable fact.