Car paint spraying with your own hands: technique of performance

In the process of using the car on the surface of the body paintwork , scratches, chips and other damage are formed. In garage conditions, it is almost impossible to restore the coating without specialized equipment. However, if you need to paint the car with minimal investment, then the best way is to paint the car with a spray gun with your own hands. This is a quick and inexpensive way to restore the appearance of the car.

Pluses of car paint spraying

The spray paint, which is contained in the aerosol can, is very easily applied to virtually any surface. In this case, the surface (in this case the body of the car) can be uneven. Also, during the painting process, no equipment is required, including compressors and a spray gun. Even with a layman, the layer will be as uniform as possible. This is not all the pluses, which provides painting with a balloon car. The advantages of such staining are in the low cost of work. Another advantage is that when using an aerosol can, no preparatory work is required before the process, and the results can strike with high quality.

When to paint

Depending on what the damage is on the body, from their level, different technologies will be used. It is important to carefully inspect the car before you can paint the car with your own hands. Instructions for the restoration of the car indicates that with the slightest chipping of varnish and paint, small and shallow scratches, a light polishing of a particular body element is sufficient. But you need to remember that polishing will only help if the paintwork around the damaged area is very tight and is not going to flake off in the near future. When the damage is serious enough, the paint has peeled off and a primer or even a metal is visible, then only painting the car with your own hands with a can of defective spots is performed. It should be noted that the restoration of the paintwork surface of the body should be carried out very quickly, otherwise the metal will rapidly oxidize and begin to corrode. Over time, the owner will have to replace the bodywork completely or use the services of welders.

Necessary materials

Although painting the car with a can is a simple process that can be performed at home, you still need to purchase some materials. Experts recommend to buy:

• Primer, putty for cars;
• Sandpaper;
• Basic enamel;
• Paint in an aerosol can of a suitable color;
• Polymer varnish without color;
• Prepare protective films or old newspapers;
• Pick up clothes, buy gloves and a respirator.

Preparing the car for the painting process

If in the process of repair any body defect is ignored, then very soon it will begin to increase. Corrosion processes will occur even under the paint. To eliminate deep scratches and significant chipping, experts recommend buying acrylic putty to remove chipped.

However, before repairing the damaged area, it must be degreased. This can be done with the help of rags. One rag should be moistened with a degreasing liquid and thoroughly treated surface, and the second should then be dried and wiped clean. If the chip has reached the metal, then the simple painting of the car with its own ballon can not help - here you need a primer. These compounds are sold in vials or aerosol cans.

Before using such a primer it is very important to protect the surface as much as possible from damage during grinding. Both the putty and the primer dry at a temperature of 20 degrees above zero for half an hour. After these compounds have dried, excess is removed with sandpaper, which is designed for dry processing. The paper must have abrasiveness from P320 to P400. The putty is removed until the geometric characteristics of the surface to be completely restored, that is, to the original shape.

The grinding process will be much more convenient if the sandpaper is wrapped around a wooden bar. After the surface is completely polished, tape or other protective coatings are removed, which are pasted to protect them from damage. Now carefully sand the edges of the surface with paper with abrasive P500.

Next, prepare the surface, located next to the repair site. Here there will be a transition from a new paint to an old one. This is done as follows - the surface must be matted with Scotch-Bright and a special matting paste. Also, the matting process can be performed using abrasive paper P1000-1200. Further - the treated area is thoroughly degreased by the same technology as in the first case. Used two pieces of rags and liquid for degreasing.

Features of local painting

Specialists share their experience with those for whom the paint for the first time is sprayed with a can. Useful tips of experts are as follows. The area on which the base enamel will be applied should not be larger than the treated zone, or go beyond its boundaries. In addition, the coating should not go beyond the frosted area to the glossy area.

Lacquer coating should not go beyond the area of the primer. It is worth noting that preparatory work on the surface should cover as much of the site as possible. This is done for the possibility of further polishing the site.

Painting a car with his own hand balloon with a transition

This technology has become very popular among car owners. Naturally, there are opponents of this method of staining, which are sure that it is practically impossible to achieve a high quality of the surface. But when you need to restore the appearance and paintwork of the body parts at minimum costs, there is simply no better method.

Painting with a transition is used to repair small defects on the surface of the body. Use this technology because the modern colors of cars make it very difficult to select suitable colors for tinting colors. Sometimes painting car ballonchikom own hands can turn into a real test - the coating has the property to fade, and then pick a shade will be very difficult. The painted area will be brighter. Difficulties in selection arise in the case of light shades, with the dark all a bit easier. For example, if you need to tint the wing of the car, the first thing you do is apply the base enamel. Any other new layer must necessarily overlap already applied. Clear boundaries are not needed - it is better to avoid this. Further, the surface boundaries for the application of lacquers and special solvents for creating a transition are identified. Painting a car with a can of one's own hands in this way will not lead to undesirable effects if you strictly observe the technology and apply the correct materials.

Basics of touching with transition

What is the painting of a car with a spray gun? The ways of working on this technology mean creating a smooth transition from the old LCP to the new one. Transition is a small chance that as a result of the work there will be no difference between the factory paint and just applied. This option is equally effective for any part of the car. However, do not forget that on the varnish surface you also need to make a transition.

Paint application

First, shake the can thoroughly. Do this in a few minutes. Next is painting the car with a can. Stages of work should include control paint application - this must be done strictly following the instructions for using a particular paint.

The composition must be sprayed from a distance of 30 cm. It is desirable to perform painting at an air temperature of plus 20 degrees. At the first stage, apply the base enamel in 2-3 layers and allow each of them to dry for 10 minutes. Any next layer must overlap the previous ones. It must be done so that with each applied layer the spot of new paint increases.

The last applied layer should be dried for about 15-20 minutes. Then the paint is covered with a clear varnish. Perform this procedure the same as with the application of paint. Enough of two or three layers of varnish, after which within 15 seconds blur the boundaries between the old and the new coating. To do this, you should use a special solvent, which is used for the transition zones. This composition is applied only by the edge of the "torch". Only the transition zone is covered. Then the surface is thoroughly polished to make the transition seem as imperceptible as possible.

If metallic paints are used, it is recommended to apply aerosol varnishes for application with the top layer. They cover a surface that has dried out within 30 minutes.

We color the car in camouflage

The idea to use a camouflage pattern was first born to the military in order to increase the level of camouflage of transport. Today, this pattern is also popular on civilian cars. Car owners no longer need to hide - they, on the contrary, want to stand out from the crowd.

Do not make mistakes

The maximum effect from such painting can be obtained only if the intensity and scale of each detail of the pattern, the nature of which is determined depending on the particular machine, are correctly chosen. This painting of the car with his own hand cans (VAZ for example) will not look the same as on BMW or any other foreign car. There is simply no universal solution. It is necessary to independently design a drawing that can emphasize the nature of the machine and the owner. But this does not mean that in the absence of universal solutions, one must forget about the rules. There are a number of nuances that everyone should know.

Mandatory use of color schemes with shades of green, sand or brown. In any other case, the concept will be broken and the machine will lose its bellicose appearance.

Painting a car with his own hand can of khaki is a stain. The dimensions and contours of each of them are set manually, necessarily taking into account the features of the body parts to which they will be applied. Also the uniqueness of the machine will grow - it will look very impressive if every spot is original.

Correct selection of materials

Choosing materials, it is important to get not only a beautiful and original, but also a durable coating. It is important to obtain a paint that can withstand the destructive effects of the environment. Even better, if the paint will have protective properties.

Creating stains

Creating a picture is a set of specific actions. On the basis of whether these actions are properly performed, it depends on whether the paint is painted with quality. Advice of professionals should not be ignored.

Black spots

That they have acquired contours, it is necessary to have a paint tape. Strips of different lengths are glued so that the lines and bends are as smooth as possible. It is important that the adhesive tape fits tightly to the surface of the body. Effectively, the large spots around the body will look. When the drawing process is complete, you can start painting them in black. Then you need to give the pattern to freeze for three hours.

Color Spots

They are made in such a way that their outlines overlap with black ones. This will make the drawing more real. You can apply brown spots or green. After each pass, the pattern should be allowed to dry for 3 hours. It is important that the entire surface of the body be covered with colored impregnations. However, do not forget about the factory color of the car.

Color spots need to be done in two layers - so the black color will not shine through. If there is no possibility to wait for three hours, the process is accelerated with the help of a halogen lamp. After all has dried up, it is possible to put a varnish and to enjoy the new car.

Conclusion

As you can see, painting from a can does not really represent anything complicated. But with the help of this method, with a proper level of accuracy, you can achieve high results. However, it is worth remembering that this procedure is performed indoors at the lowest possible humidity (clean and dry garage is an ideal option). Otherwise, the paint will not last long.