Underwater camera for fishing with your hands. How to make an underwater camera for winter fishing?

Requirements for underwater cameras are strict. In this case, the tightness of the housing is assessed. Pressure underwater camera for fishing must withstand large. Many lenses are not suitable for this. It is also important to mention lighting. Self-assembling the camera at home is possible. However, in this case it is necessary to determine all the components.

Cameras with a common matrix

This underwater camera is made for fishing with their own hands using a high-frequency compression unit. In this case, you will also need two LEDs. However, in the first place it is important to assemble the body of the model. Some experts recommend using a plastic pipe in this situation. The lens must be installed immediately with the module. It is required to connect to the flash drive.

It should also be noted that a self-made underwater camera for fishing will not work without a CPU. It should be installed near the compression unit. The matrix is chosen low-resistance. In the end, the underwater camera for fishing is equipped with a battery and an output port.

Use of compression units at 50 Hz

It is done with a 50 Hz block underwater camera for fishing with their own hands is quite simple. In this case, a plastic pipe of a small size fits perfectly. Some experts additionally wrap it with polyethylene film. LED lamps to the device are connected via a conductor.

The lens can be selected with the module. The filter itself will need an optical type. After installing the matrix on the unit, a special prism is attached, which is intended for transferring the image to the central processor. To save data, the underwater camera for fishing is equipped with a flash drive. Batteries in this case can be used finger.

Application of compression units at 60 Hz

It is done with this unit underwater camera for fishing by own hands only with the help of a matrix with a converter. For winter fishing, this model will work well. Directly the lens is recommended by many specialists to be selected with the module. However, the filter is a good one. It is recommended to start the assembly of the camera with the block fixed. Next, you should do an optical filter. After soldering the matrix, LED lamps are attached. In this case, one is not enough for sure. Next, it only remains to install batteries and a flash drive with an output under it.

Using a chromatic capacitor

The underwater camera for fishing with their hands is going to be quite difficult with a chromatic compressor. The problem in this case is that you need a low-frequency compression unit. Find it in the store is difficult. Also, the assembly of the model requires a high-quality lens. The body itself can be made with a plastic pipe.

In this case, a high density polyethylene tape should be used. However, in the first place, it is important to fix the condenser. For this purpose, it is necessary to solder the matrix immediately. Next, you need to install an optical filter. Directly the lens is a good modular type. The CPU must be connected only after the flash drive. Also, the underwater fishing webcam is equipped with a shutter. Use it more appropriately from the camcorder. Batteries in this case can be used finger.

Camera with magnetic filter for winter fishing

The camera for underwater fishing photography with magnetic filters is widely used today. In this case, its advantage lies in its compactness. The compression unit can be used even at 50 Hz. The body itself can be made from a can. In this case, a sealed plastic bag is required in advance. However, in the first place it is important to do the device matrix, as well as the lens. For this purpose, the CPU is installed in the case. Flash drive in this situation you can use a small. The shutter must be installed near the compression unit itself. The last thing you need to do is battery and port.

Model on a convection condenser

On the convection condenser, the underwater camera for fishing reviews, as a rule, gets positive. Even at great depths, it behaves normally. To assemble the model on its own, you will need a durable and long plastic housing. As insulation it is necessary to use polyethylene tape. You need to stack it in several thin layers. The capacitor in this case will be installed near the matrix. However, in the first place, the compression unit is prepared. With this capacitor, it is better to choose it at 55 Hz. At the same time, many experts recommend using the matrix with two converters.

All this will allow you to take pictures in high resolution. However, the lens must match the matrix. In this case, many prefer a model with optical filters. Directly magnetic analogs wear out quickly and are expensive in stores. After installing the compression unit, a prism is fixed in the camera body.

The gate in the device should be located near the condenser. To connect the flash drive will have to use a blowtorch. At the end of the job, you need to install the port. In some cases, a thermal relay is used for such cameras, but it consumes a lot of energy from the battery.

Device with dipole diode

An underwater camera for winter fishing with dipole diodes is made very simply. To this end, the compression unit will need a standard 50 Hz. In this case, the lenses are only modular. The case is standard plastic. Matrices for these purposes are suitable with a single converter. Directly, it is more expedient to set the optical type.

The central processor in the camera body must be attached to the compression unit. After fixing it, you can start installing the flash drive. In this case, for the battery, the ports are placed at the matrix. At the end of the work, LED lamps are selected for lighting.

Application of silicon diodes

Underwater camera for winter fishing with silicon diodes in our time is in great demand. First of all, the models stand out because they do not consume much electricity. In order to fix them, you need to use the compression unit only at 60 Hz. In shops it can not be found. Directly the matrix is mounted on two transducers.

Lenses must be attached to the compression unit. In addition, you need to provide a place in the body for the shutter. You can use it from any video camera. The flash drive is connected as standard directly to the matrix. Further, it remains only to solder the CPU. The battery port must be installed in the back of the camera.

Using low-sensitivity resonators

Low-sensitivity resonators for the assembly of the camera fit well. However, the matrix for this needs to be selected with one converter. All this will allow, in the final analysis, to put the usual block of compression on 50 Hz. It is more expedient to install filters in the chamber of an absorbing type. However, first of all you need to take care of the lens.

In some cases, it is put on the seal. So, you can not worry about water leaks. The central processor in such models is located just behind the compression unit. The battery should be at the back of the camera.

Use of high-sensitivity resonators

High-sensitivity resonators allow you to shoot high-resolution images. However, it should be borne in mind that the battery will then be discharged quickly. Begin the assembly of the model with the installation of the compression unit. Next, we must deal directly with the resonator. In order to install it, you must first put the matrix.

The next step is to prepare an optical filter. Magnetic analogs for such cameras do not fit uniquely. The flash drive can be used small. The CPU must be installed at the compression unit. In order to install a serial port, you need to fasten the shutter first. At the end of the work, the battery is put.