The instruction on the repair of the motor-block "Cascade". Rules of operation motoblock

Faults motoblock can be divided into two categories: motor problems and problems with all other mechanisms and nodes. If in your arsenal there is similar equipment, then in the process of operation, with the greatest probability, you may encounter engine problems.

Motor problems

The repair instruction for the Kaskad motoblock, presented in the article, will allow you to understand what malfunctions could have occurred with the engine, and how to eliminate them. The motor may stop running if it can not be activated, then a spontaneous stop, a lack of power set and a fault may indicate problems.

If a petrol engine is installed in the device, it is necessary to check whether there is fuel in the tank, what is the condition of the carburettor air damper, how the ignition is switched on, and whether the fuel is injected into the carburetor. To check the last condition, it is necessary to fill the float chamber by using the appropriate button. At the same time, the fuel should be poured out of the hole in the cover of the float chamber. If the gasoline runs in a thin stream or it is not noticeable at all, this may indicate a contamination of the fuel filter or the clogging of the air valve. The repair instruction for the Kaskad motoblock in this case provides for the cleaning of the valve or filter.

Problems with fuel entering the carburetor

The fact that the fuel enters the cylinder of the motor, can indicate the state of the candle. It is recommended to check it by unscrewing the cable from the cylinder cover. If the candle is dry, this indicates that the fuel mixture does not enter the cylinder. If you managed to establish that the fuel enters the carburetor, a possible cause of engine failure from startup may be contamination of the carburetor filter grid.

Sometimes jamming leads to malfunction. If these conditions are met, the repair instructions for the Kaskad motobloc provide for the removal of the carburetor, disassembly and cleaning of the element. These works can be made without visiting the service workshop.

Checking the condition of the candle

The repair instruction for the Kaskad motoblock, which you should be familiar with before carrying out the work, will allow you to understand how to inspect the state of the candle. If it is wet, the gasoline enters the cylinder. Failure to start can be the result of an excess of fuel mixture. If the surface of the candle is excessively covered with gasoline, it is necessary to dry the cylinders, pump the engine with a starter, leaving the candle in an inverted state. Before this, the master must shut off the fuel supply. The candle can be contaminated with carbon, while it is cleaned with a fine skins and gasoline. It is important to analyze the value of the gap between the electrodes. If required, it must be adjusted, following the requirements provided by the manufacturer in the manual. The size of the gap should be 0, 8 millimeters.

Ignition system problems

Ignition of the Kaskad motoblock can also fail. If this happens, you need to check the condition of the candle, clean it and adjust the clearance. In parallel with this, it is necessary to analyze whether there are damages in the electrical circuit. The master should check which gap is kept between the yoke and the coil. For different models of the manufacturer, recommendations for carrying out these tasks are specified in the instructions.

Problems with the carburetor

The carburetor of the Kaskad motoblock may be contaminated, in some cases it may be improperly adjusted. If this happens, then this node is removed and cleaned, its adjustment is made, which should be provided by the instruction.

There may be another problem, which is expressed in the fact that air enters the carburettor in insufficient volume. This can happen due to the contamination of the air filter, eventually the fuel mixture is re-enriched. During operation, you must periodically clean the air filter to avoid the described trouble. However, if the equipment is used in excessively dusty conditions, more frequent cleaning may be required.

You must analyze the condition of the air filter. Depending on the material in the base, you need to rid the element of dirt in one of the appropriate ways. If the carburettor of the motor block "Cascade" began to receive air in insufficient quantities, it may be necessary to clean the paper filter, which is made by a slight tapping or blowing. If there is a foam filter, you can rinse it and then dry it well. The strainer is purged by a vacuum cleaner. These elements have their own service life, as soon as it is developed, the node needs to be changed.

Motoblock adjustment

Adjustment of the motor block "Cascade" is initially made in the conditions of the plant. But if you need to adjust the carburetor, then you need to do it using the technology that provides for the first stage of wrapping the two screws to the stop, while doing a lot of effort is not necessary. Further, the screws are turned off by 1.4 turns, the engine must be started and warmed up. The throttle lever is set to the position that corresponds to the minimum possible rpm. The master must establish a stable idling speed. The last operation must be repeated until you have achieved uninterrupted operation of the engine at idle.

Motoblock "Cascade", the instruction manual of which will allow you to exclude the need for premature repairs, may provide for the correction of the engine. At the same time, the corresponding screws are turned away or wrapped up to get a stable operation.

Rules of operation

The Cascade Motoblock, the instruction manual of which will allow you to use the equipment with maximum efficiency, should be periodically subjected to maintenance, this concerns cleaning, refueling and washing. When carrying out these manipulations, the engine must be stopped. All adjustment work must be carried out with the motor stopped, this requirement does not apply to adjusting the carburetor. Operation of the motor block must be carried out with protective covers.

Specifications

Characteristics of the motor block "Cascade" will allow you to make the right choice. This device is a universal mechanical means, which will become an effective assistant in the performance of work on the backyard. If it is a question of small areas, it is possible to prefer light or average motoblocks, the weight of which does not exceed 120 kilograms. If you are faced with the task of processing a land area of a hectare, you will need an industrial heavy machinery.

The device has two rear or front gears, and the speed is 8.3 and 3.7 kilometers per hour. If you want to choose a model for solving problems on the territory of your own site, you can purchase a model, the mass of which is 103 kilograms. This motoblock has rather limited dimensions: 83x48x74 centimeters.