Shtroblenie surfaces for wiring: regulations and tools

Any room, regardless of its destination, requires periodic repairs. Paving electric wiring is a very important stage of construction and repair work, therefore, before starting the stitching of surfaces, it is worth coordinating several important issues with family members, the designer, clarifying the established standards and the possibility of implementing the desired requirements in practice.

Standards

The location of lamps, chandeliers, sockets, switches must be agreed in advance with those people who make the project part of the premises and participate in their daily use. In addition, the customer works must have a permit, which is issued in the relevant authorities, as the construction documentation contains standards that can not be violated in the conduct of construction work related to the stonecutting of walls.

How to post in the house if its walls are concrete? Monolithic construction technology and brickwork, the thickness of which is more than 30 cm, can produce strobilenie. In a panel house, such work is prohibited. But users have the opportunity to replace electrical wiring in the panels available in the panels or plastic boxes.

Hammer drill

Shtroblenie surfaces can be carried out by various construction tools. When working with brick and concrete walls, specialists use a puncher, but before commencing work, they make markings.

The layout of the posting route is performed after the final location of the final devices has been fully approved. Shtroblenie for wiring occurs by drilling holes, the pitch of which does not exceed 2 cm, and connecting them by switching the perforator to the "hammer" mode. The partitions are removed at an angle of 90 ° with respect to the axis of the holes obtained.

Experts, before stretching the cable, install switches, boxes under the sockets. After this, the closing step is followed.

Bulgarian

How to post in the house, if there is only a Bulgarian from the construction tools? You need to take care of the presence of a diamond disc. In tandem, a construction tool is produced, with proper use of which you can trail the route for wiring. But without a puncher in this case, nothing happens.

Before you start to work, the surface must be plastered. Shtroblenie surfaces occur on previously marked trails. The furrows cut through the furrows, and the perforator in the "hammer" mode removes a section of the wall located between them. Using this method, you can get smooth, high-quality edges.

Stroborez

Shtroblenie surfaces with this tool is the best method for obtaining a quality result in a short time without dust. A high level of strob can reduce the cost of additional work.

Compared with the perforator and the Bulgarian, physical efforts are minimal when a shroud cutter is used. This tool, in tandem with an industrial vacuum cleaner, allows you to perform high-quality stroblenie. The price of services (which is usually $ 1 per meter of strobes) is no longer of interest to customers after they learn that all work will be done without dust and debris. A professional tool is equipped with a pair of diamond discs, so you can cut both lines at once. The width and depth of the bar are set independently, depending on the required and permissible specifications, parameters.

Professional equipment of this kind should be used by qualified specialists. This affects the quality of the work performed and the safety when performing them.

The final stage

After the process of shtrobleniya is over, the wire is laid, the final stage of the electrical wiring is coming . Putty strob is an equally important stage. Professionals of their business know the subtleties of this stage, but not all conscientiously refer to it. If the customer monitors the whole process, he should pay special attention to what layer putty putty. Qualified specialists apply it in thin layers and wait for complete drying before applying the next layer. This happens until the thickness of the material is equal to the level of the surface.

The first sign that the requirement of complete drying of the layers was not observed is the unevenness of the surface of the strob. The color of the dry putty should be identical to the shade of the wall. When pasting walls with wallpaper, you will not see the places in which the stitches were previously. If the color of the wall and the sealed fence is different, it will be noticeable through thin wallpaper.

Only the experience of a specialist depends on the result. Shtroblenie surfaces - this is a very time-consuming and responsible process, which can be performed only qualitatively by a professional. There should be no errors in the replacement of the wiring , otherwise they can lead to disastrous consequences.