How to properly stick a corner on the bath: technology and recommendations

The bathroom has many items. For proper operation of plumbing, you should consider all the details. Even such an imperceptible at first glance accessory, like a plastic curb, plays an important role. How to properly stick a corner on a bath should be studied before starting work. Both functional and aesthetic qualities of the product depend on this.

To stick a corner on a bath is not difficult. The main thing is to follow all the steps carefully. In this case, the water will not seep onto the floor, stagnate in the joints. Step-by-step instruction on gluing a curb on the bath will help to make everything right.

Corner Assignment

The plastic corner on the bath is installed to seal the joint between the plumbing equipment and the wall. It prevents water from flowing to the floor.

To understand how to correctly paste a corner on the bath, you should study the technology presented below. By doing the right thing, you can reduce the humidity level in the room. It will not form a fungus, and metal objects will not be rusted.

In addition, water leaking to the floor can leak to the ceiling of neighbors from the bottom. It will ruin expensive repairs, which will have to be compensated out of your pocket.

The choice of the best option for gluing the plinth to the bath affects a number of factors. These include the size of the gap between the wall and plumbing, the type of surface finish, as well as the amount of funds that the owners have allocated for the purchase of this accessory.

Types of curbs

Getting acquainted with the technology, how to install the plastic corner on the bath, first determine the desired type of product. On sale there are curbs with factory glue coating and without it.

In the first case, there is a high probability of flaking the plinth from the surface. The factory glue coating does not have good strength. This is especially noticeable in conditions of high humidity.

If the bath is not rigidly attached to the wall, there is more or less of its vibration. This will also cause seam loss. Therefore, experts recommend to adhere to the technology of gluing a curb on a bath in which a clean corner participates.

Skirting boards made of plastic can be rigid or in the form of tape. On sale there is a large number of variations of forms, colors of such products. There are no big differences in their installation. How to install a plastic corner on the bath, is discussed further.

Solid skirting boards and their installation

A plastic skirting board for a bathtub is easy to install, so anyone can properly glue it. In addition, the cost of such products is relatively small. This makes solid plastic curbs so popular.

When buying it, pay attention to the width of the product. It depends on the gap between the bathroom and the wall.

Most often a corner of PVC is presented in white. But there are other options that allow you to fit it into any type of interior.

This is a versatile corner in the bathroom. Than to glue PVC-border, experts give advice. Best, in their opinion, fit "liquid nails."

To paste a border on a bath it is possible on a ceramic tile or under it. In the first case, the corner closes the joint between the plumbing and the already finished coating. In the second variant, you will first need to glue the curb, and already on it lay the cover on the wall.

Belt plinth and its installation

There are several options, than you can glue a corner of the corner on the bathroom. Often this product already has a layer of a special fixative substance. However, if the owners are interested in the question of how to glue the plinth on the bath qualitatively, you should still choose another sealant.

If desired, the factory glue can be carefully removed from the polyethylene product. This is done with a knife. The main thing is to follow all the steps carefully.

Sometimes such a fixation layer is left, but in addition use a silicone sealant.

The different width of the ribbon will also help to select the desired curb. It is even easier to install than a hard corner. However, it is used in the case of rigid fixation of the bath.

Adhesive for corner

The border, by its nature, does not close the gap through which water seeps to the floor. It serves as a decorative element that covers the sealant layer.

To understand how to properly glue a plinth for a bath, you should imagine its appearance at the end of the work. Color sealant, emerging from under the corner, does not add beauty to the general appearance of the room. Therefore, transparent varieties of glue should be used.

If the bath is white, then the sealant of a similar shade will also look pretty good.

Also, the fixative substance must be quickly caught, otherwise it will take a very long time to hold the corner manually.

It should be taken into account the fact that in case of gluing a curb to the acrylic bath, it is necessary to choose a plastic sealant. It must be sanitary. The composition of such glue includes additives that impede the development of the tribe and microbes. Acrylic sealant is not suitable for bathroom conditions. Therefore, water resistant adhesives should be purchased. They are silicones.

Preparing for installation

Before you paste the curb on the bath, you should prepare the base. This process is especially important for replacing the old corner. It is carefully dismantled and removed from the wall traces of old glue. To do this, you need to use a knife.

It is necessary to clean off dirt and old sealant gently so as not to damage the bath and the coating on the wall. Wet rag should be carefully wiped the place where the old plinth was installed.

Disinfection is then carried out. This procedure is also carried out for a new coating during repair. You can just use bleach. Today, there are many sanitation facilities for disinfection.

Clean the substrate thoroughly. To do this, you can use a conventional hair dryer.

Curb measurement

Before buying a new product that prevents water from entering the floor, you should correctly measure the bath. To do this, tape measure its length and width. Next, two skirting boards are purchased in accordance with the dimensions obtained.

Houses at new corners mark the length. Then the main stage of solving the problem begins, how to paste the curb on the bath. A step-by-step instruction will help you understand the sequence of actions.

Using a hacksaw for metal and using a construction chair, the corner is cut off from both sides. This must be done at an angle of 45 degrees. Then you should attach a curb to the bathroom and check the dimensions.

Bonding the corner

Applying the plastic skirting to the bath, with the second hand paste the paint tape 2 mm above the upper edge of the corner. A similar operation occurs from below.

It is recommended to make a bath with newspapers. This prevents its contamination with glue. The corner is retracted. On the walls and sides there is a paint tape. Master then nothing remains, except how to paste the curb on the bath. The technology and recommendations of experts suggest the use of a construction pistol at this stage. With it, a layer of glue is laid, starting from the corners and around the edge.

The corner is applied to the contour of the sealant, pressing it lightly against the base. You can come up with an emphasis that allows you to squeeze the curb and wait for the glue to stick. This lasts about 20 min.

The final stage

When it's half an hour after pressing the corner, the excess adhesive is peeled off. Then, with white sealant, the places of adherence to the wall and bath are treated.

To do this, on the curb, as well as above and below it, again apply a sticky tape. There is one more nuance of how to correctly apply a corner to the bath. Using a spatula, the edge of the plinth should be moved away and a white sealant should be inserted into the small space that has been formed.

Rubber spatula smeared and leveled the substance throughout the seam. This is done from above and below the corner.

Next, the paint tape is carefully peeled off. Should get a smooth beautiful seam. It dries, according to the manufacturer's instructions, a certain time. Apply sealant should be thin, but a solid line. The point technique is inadmissible in this case. There should be no voids along the entire surface of the joints. They should be uniform.

This completes the installation process.

Having become acquainted with the technique how correctly to stick a corner on a bath, it is possible to perform work qualitatively. The border will at the same time reliably protect the joints from the flow of water through them to the floor, and will also help reduce the humidity level in the room. A neatly glued corner will give the bath a well-groomed look and will protect the seams from the formation of the fungus. Carrying out all the actions according to the instructions, everyone can perform this work independently.