How to make a beach canopy from the sun with your own hands

If you are a lover of relaxation on the beach, then for you will be a real find home-made canopy from the sun. When compared with a large umbrella, you can make sure that it is cheaper, because it is made from improvised materials, and it is easy to make it yourself, in a garage or at home. The design differs insignificant weight, is demountable, thanks to what it can be laid even in a backpack.

Preparation of materials

If you decide to perform a canopy from the sun, then you need to prepare certain tools and materials:

• Hand drill;
• PVC pipe;
• Bolts;
• Tent pegs;
• Rubber hammer;
• Plugs;
• Washers;
• tarpaulin.

To carry out the work it will be necessary to modify the stubs, but this will be discussed below.

Recommendations for the manufacture of a canopy

When a canopy from the sun is constructed using the above materials and tools, the plugs must be modified. In each of them holes are made for the bolt, the fasteners must be inserted together with the washer and nut, and then tighten well.

The next step will be the installation of plugs on long PVC pipes. The plugs must be clogged with a rubber mallet. This will establish them more thoroughly. At the end of the pipes on the other side, PVC adapters should be installed, the master must walk through the rubberized hammer. At one end of the fourth pipe, it is necessary to install plugs without bolts, whereas on the second - adapters. This will provide a support structure for the awning. With the help of a coupling, these blanks will be turned into high sticks for the front part of the canopy, behind the two short ones will be located. At the top of the part you need to make holes, through which will pass the paracord.

When a canopy is used from the sun, it should be supplemented with a tarpaulin or any other cloth. Through the corners of the material, the paracord is skipped and stretched in different directions. The ends of the rope should be tied to the stakes and clog them at an angle to the cover. At one of the corners of the front of the structure, you need to install a long pipe. The obliquity is short. The tension of the tarpaulin can be adjusted with a rope, passing it through the holes that are in the upper part of the pipe. Once the two pipes have been installed, the parakord should be adjusted again. Bolts must pass through the notches in the tarpaulin, this will help increase the tension of the fabric. The received fastening needs to be fixed by means of one more nut, only then the covering will not fly off at gusts of a wind. On this we can assume that the canopy is ready. They can be used.

Alternate canopy

Masking mesh for the canopy from the sun can act as a roof. But the second version of this design can be made by you using a simpler technology. To do this, prepare sticks, linen cloth, rope, pegs, nails. These tools and materials are easy to find in a garage or house, in a pantry or in an attic. Thus, the canopy will be completely free.

The sticks will serve as supports for maintaining the tent. You will need 3 blanks, which can be made of aluminum or wood. To create a frame, supports are needed, the length of which can vary from 110 to 150 cm. You need to prepare two such elements, whereas one stick will have dimensions from 200 to 220 cm, but the thickness of the support will be 25-30 mm. Having found a rope or twine, you must cut it into four pieces, each of which will not exceed 1.5 m in length. You can borrow pegs from an old tent, fit and cut from the wood yourself, their length should be equal to 45 cm, at their ends You need to drill holes for the rope or install self-tapping screws, which are left half-screwed. Need two nails, the length of each of which will be approximately 80 mm.

For reference

Such a beach canopy from the sun will not last long, it is not intended for repeated use. This is due to the fact that the design is carried out in a hurry.

Build process

On two sticks, or rather at their ends, it is necessary to hammer nails to half the length. The remaining stick should be used in order to drill holes at its ends with an indentation from the edge of about 5 cm. On this we can assume that the frame is almost ready. If the tubes are made of aluminum, the studs are wound with an insulating tape.

When you perform a beach canopy from the sun, in the next step you can take up a cloth whose width should be less than the distance between the holes on the supports. Excess can be cut or tucked in place. The length of the sheet is usually about 220 cm, you can take it. Now the master uses a knife or scissors to make holes in the corners of the awning. In them the prepared rope is passed, which is tied to knots. The material must be connected to the supports of the future canopy.

Now we only have to put everything together, for this purpose two racks with nails on the ends are piled on the bank, the nails are mounted on crossbeams with holes, it is possible to hang the tent in width, the hanging edges will be located in the center. Prepared pegs must be driven into the ground with a hammer.

Stationary canopy

Canopy from the sun and rain can be made and in the form of a stationary structure. To do this, you should prepare gravel, sand, wooden beams, as well as cement. It will take a fastener for the carcass, as well as a mixture for disinfecting wood or protecting the metal from corrosion. The roof can be covered with polycarbonate. But if the canopy is fabric, then a canvas or any other dense material, for example, a polymer cloth made of polyamide yarns, will do. When sunshades and rain canopies are made for cottages, wood can be used.

At the first stage, a site for construction is selected, then on the site marking is carried out with the help of cords. It removes soil to a depth of up to 15 centimeters, and in the corners settle nests for supports. On the perimeter can be installed a wooden blind area of the boards, a sand-gravel pillow is poured into the recess.

The process of assembling the frame

Pipes or beams are cut vertically in size taking into account the length of the buried part in the ground. At the bottom of each nest should be covered with gravel and sand, which are well condensed. After installing the support, it is necessary to align with a plumb bob, after which they are concreted. From above, such elements can be joined by thin bars or pipes, which will allow forming the upper strapping.

The most common construction for a roof is a semicircular shape. In this case, metal arcs from the pipe can be used as the supporting frame. Masking mesh for the canopy from the sun can also be purchased and installed, while you can arrange a picnic, without fear that your family will be overwhelmed by mosquitoes.

Forming the roof

When polycarbonate is chosen for a canopy, it should be cut to size, the protective profile is put on the ends. Polycarbonate is reinforced to the rafters with self-tapping screws, and gutters must be installed at all angles. Mesh for the canopy from the sun will be the best solution for recreation. It is strong and durable, it can have different sizes, for example 6 x 9 m, 3 x 18 m, 6 x 6 m.