How to connect a gas stove in the apartment yourself. Installing the gas cooker

Every woman knows that a gas stove is the most convenient device that is in almost every house and is necessary for cooking any food. At the same time, this is a rather dangerous household appliance, because the connection is made to a gas cylinder or gas pipe. How to connect a gas stove in an apartment on your own is not known to everyone, so below it will describe what requirements must be met and that you may need to install the device and its connection passed without excesses. First, when working, it is necessary to strictly follow the instructions attached to each plate, observe the safety rules.

Organization of a place for a gas cooker

When you choose a place where and how to connect a gas cooker, you must take into account the mandatory rules of technical safety. Therefore it is necessary to know the following:

- the slab can not be located beyond four meters from the metal pipe of the gas pipeline;

- modern gas cookers necessarily have electric ignition and lighting in the oven, so near the plate itself there must be a modern socket with ground;

- As a flexible wiring can be used different types of hoses: rubber, having a metal braid (it is considered a good option to safely connect the plate), rubber-fabric (a fairly flexible hose, it does not pass current, but it is not hard enough);

- hoses intended for water are marked with blue and red marks, and for gas - yellow, so they will be difficult to confuse;

- the harshest hose, but at the same time costly is considered a bellows hose.

Pay attention: it does not matter which sleeve you choose. To install the gas cooker successfully, the main thing is that its internal diameter is at least 10 mm. This is necessary for good passage of gas to the oven and all the burners.

What you need to install

1. The locksmith key or the swivel key is 22, 24, 27.
2. Crosshead screwdriver.
3. Gas key number one.
4. Flax (but it is better to replace it with a tape FUM).
5. A gasket having a diameter of 13 mm (most often it can be taken from a plate assembly).
6. Sealing thread.
7. Emulsion from a soap solution (it is used to check for a gas leak).
8. Ball valve for 13 mm.
9. Gas hose of the required length.

How to dismantle an old gas stove

To answer the question "how to connect a gas cooker", you must first decide what to do with the old unit (install a new one or replace the parts with an old one). First of all, before you start dismantling the old gas stove, you must close the gas valve. After you have verified that there is no gas supply, you can proceed to unscrew the locknut and strangle the coupling on the lowering of the gas stove. From old plates the coupling is difficult to remove, as it is often covered with several layers of paint. In this case, it will be advisable to cut it down with the help of a Bulgarian, the rest will be unscrewed.

After that, the slab can be moved away from the wall to provide access to the taps on the back wall. With the help of the necessary wrench, the drive from the crane is unscrewed. In the event that a new gas stove is planned to be put up a little later, then instead of hitting it put a stub.

Installation and connection of gas stove in the apartment

In flats, the gas hob is mainly connected to a pipe with central gas supply.

After the old equipment is dismantled, you can proceed to install the gas stove. First of all, the new device should be freed from the packaging, leaving only the protective film (it will be removed after installation). Put aside all the components that came with the stove (pan, pan and other). Then, with the help of the level and the adjusting feet, it is necessary to align it. Between the gas stove and the wall it is necessary to leave a small distance.

After the installation of the gas stove, a gasket with a diameter of 13 mm with a metal mesh is installed in the place where the hose and the plate are joined. It is necessary that during operation the household appliance does not get dirt and debris, which will significantly increase its service life.

This connection is tightened with the correct size wrench. Using a soap solution, the tightness of the unit is checked as follows:

- in a small mug or dish, dilute a bit of a thick soapy solution;

- fully open the gas cock, the handle must be parallel to the gas pipe;

- with a brush or fingers, carefully coat the hose connection.

In this case, you need to carefully look, whether there are bubbles on the surface of the soap solution. If there are none, the connection is good and the gas does not leak. And if there is - close the valve and tighten the assembly again.

Features of choice of gas stove for connection to the cylinder

In a private house or in the country, central gas pipes are often missing. In this case, you can connect the gas stove to the cylinder. The use of such equipment in the kitchen will have certain nuances, such as installing the plate and its connection.

Bottles usually contain natural gas, supplied at a pressure of 3.6 kPa. This is an important factor when choosing nozzles and an adjustment valve for installation. When choosing a plate in which gas will come from the cylinder, it is important to consider the following points:

- Convenience and ease of use;

- number of burners;

- plate dimensions and weight;

- Equipping with a jet;

- availability of additional functions;

- if adjustable gearboxes are included, this will considerably simplify the solution of the problem of how to connect a gas cooker;

- not all gas stoves are designed for connection to cylinders;

- individual features of some plates, which are intended only for a certain type of fuel.

Installation and connection of the gas stove to the cylinder

Independent installation of gas equipment is prohibited. This requires the help of a specialist. Since it is because of improper connection and use of the gas cylinder that a huge number of accidents happen.

But not always in the countryside there are necessary specialists, therefore, adhering to the rules written below, you can learn how to connect a gas cooker:

- According to fire safety rules, the gas stove must be installed at a distance of at least one and a half meters from the gas cylinder;

- the ideal option would be if to install a balloon on the street to equip a special metal box that would be locked;

- the gas cooker should be installed in a well-ventilated room;

- if during the operation of the cooker you feel the smell of gas, immediately it is necessary to close the gas valve and open all windows and doors for ventilation;

- periodically check that the hose remains intact, and its connection with the plate is hermetic.

Installing the hood

Installation of the hood, as well as the installation of a gas cooker, should be performed only by specialists. But if you find such difficult, you can do it yourself in accordance with safety rules.

The hood should be installed above the gas stove at a height of 650-800 mm. This will ensure the necessary safety and protect the hood from heating. Also, this height is set in the expectation that the control panel should be convenient and easy to reach.

Do not forget about the width of the hood, it should be the same as the stove, or a little more. This will help ensure good ventilation of the air above the gas stove.

Basic requirements for installation of hoods

1. The air vent is made up of small straight parts.
2. When installing the hoods, try to avoid the bends of the corrugation as much as possible.
3. If you need to change the diameter of the air vent, use adapters that are attached directly to the hood.
4. From the inside, the air vent should have a smooth surface.

Now you know everything you need, and you can easily connect the gas stove yourself and save your family budget.