Gate and gate from the metal profile with their own hands

In the market of building materials, a modern consumer can find many options for the manufacture and further installation of the gate. However, professional companies and individual developers continue to prefer profiled flooring, despite the fact that, in addition to it, the product range is replenished with new solutions that are more modern and technologically advanced. Such a high popularity of profiled flooring is due to several reasons, among them we can highlight durability, strength, attractive appearance, and democratic value. Cloths are manufactured in the conditions of the plant with the use of steel sheet on the technology of cold rolled products. On both sides the material is protected by a layer of galvanizing, which is able to protect against premature failure and corrosion. In order to achieve higher decorative qualities, the sheets are covered with a polymer layer, the shades of which can be very different. In order to produce a gate and a gate made of corrugated board, it will only be necessary to help one more person and a couple of days off.

Preparatory work

If you are going to make a gate and a gate from a metal profile with your own hands, then first you need to prepare the supporting poles and dig holes for their installation. Supports can be made of a wooden beam, you need to choose a material, the cross-section of which should be equal to 150 x 150 millimeters. The material can be a round solid log with a diameter equal to 20 cm or more. Suitable and channel beam, it is important to prepare one that will have a thickness ranging from 14 to 16 millimeters. A profile pipe with a section of 80 x 100 millimeters is often used. The product must have walls with a thickness equivalent to 7 millimeters. Once you have decided on the material that will form the basis of the supports, you can begin digging pits. Their depth should be equal to 1/3 of the height of the pillars that will rise above the ground. In this case it should be taken into account that the gate leaf, as a rule, is 0.5 meters smaller than the supports themselves. This stock will guarantee the lifting of the lower edge of the structure from the ground by 30 cm. It is necessary to leave another 20 cm above, which will be useful for strengthening decorative elements by welding.

Features of preparation

If a wicket from a metal profile is made by oneself, it is important to ensure the stability of the entire structure. This characteristic will depend on the strength of the poles. Therefore, it is recommended to choose steel rolling. For the installation of profile pipes or channel beams, a pit should be prepared, which should be buried 1.2 meters. It is important to excavate so that the borehole has a diameter of 20 to 50 cm. Prepared steel supports should be lowered into the pit, exposing the elements in a level strictly vertical. After the grout is poured. It is important to properly prepare the poles, clearing their surface from rust and priming. At the last stage, the data of the blanks are colored. From above, it is necessary to install plugs, which will prevent rain and snow from getting inside.

Select profiled sheet

If you will make a gate from a metal profile with your own hands, it is important to choose the right material. On the market you will find three groups that differ in height of the rib, thickness, and also strength. The marking "C" defines the wall profiled sheet, which is made of galvanizing of insignificant thickness. It has a small rib height. Marking "HC" represents a sheet that has a more impressive wave height. The cloth is characterized by a large thickness. The material labeled "H" is a bearing corrugated sheet, which is used for the arrangement of roofs and iron hangars. The gate and the gate from the metal profile with their own hands should be made of material under the brand C8 and C10, the thickness of which varies from 0.4 to 0.8 millimeters. The leaflets from such a canvas will weigh 40 kilograms.

Council of the master

Before starting work, it is recommended to order the cutting of the profile sheet according to the required dimensions in the factory. For this, it is best to use special equipment that ensures the accuracy of the cutting line, the accuracy of cutting and minimizes possible damage.

Carcass fabrication

If you will carry out the gate and gate from the metal profile yourself, the frame is best done using wooden beams, as an alternative solution is a profiled pipe. When choosing the latter, note that it should have a rectangular section of 40 x 20 millimeters. The walls of the pipe should be equivalent to 2 millimeters. If the poles were installed metal, then the frame should be made of a similar material. Assembly should be carried out on a flat site, which holds at least one leaf. To form different angles, you should use a square. With the help of the profile it is necessary to form, and then make the frame, which will have the form of a rectangle. The corners are additionally fixed with steel corners, which are able to give the design more impressive rigidity. The long sides of the frame system should be divided into 3 parts and fixed to the marked places of the bridge, which will be oriented in parallel. Among other things, it is important to strengthen the connections with steel corners. In these places you need to install the gate hinges.

Setting the gate to the sash

If a wicket from the metal profile is made by one's own hands, the installation of which is made in one of the wings, the frame should be made a little differently. Thus, with the help of transverse and longitudinal bridges in one of the leaflets, it is necessary to fix to a rectangular frame. The master must create a frame system of the wicket, which will have dimensions equal to 80 x 180 cm. The location of the loops is important to shift to the top and bottom edges of the gate.

Sheathing of the frame by profile flooring

If you will make a gate from a metal profile with your own hands, the scheme of which will help you in carrying out the work, then the frame should be finished after the frame assembly. To fix the profile, it is necessary to apply fasteners by the type of screws equipped with a hexagon head.

To the gate hinges, woven fabrics with a wavy surface should be fixed with bolts, as an alternative solution you can use fixing by welding. The length of the loops should not be less than 1 meter, while the thickness - not less than 3 millimeters. When installing the assembled flaps, it is recommended to use a winch that is installed on a beam laid over the poles. On the ground should be laid bruski, which are mounted gate leaf. This will allow you to fasten the loop on the pole by welding. For safety, the hinges are additionally fixed with bolts. If you are thinking about how to make a wicket from the metal profile with your own hands, then after the bars should be removed to check how easy it is to close and open the whole structure.

Conclusion

The wicket from a metal profile by own hands without welding is made only in the event that the master does not possess skills of work with the welding device that happens seldom.