Mounting the imitation of the log with your own hands: instructions, technology and recommendations

Each owner of a private house knows that the appearance of the home is just as important for the convenience of living as the inner comfort. Eco-friendly and modern material today is a simulation of the beam. It is a panel that is installed by a certain technology. If you observe the accuracy during installation, you can achieve a quality finish that will please the family for several decades.

Simulation technology

Installation of the imitation of the beam is carried out in several stages, among them:

• Choice of material and components;
• Preparation of walls;
• Installation of a lath;
• Work on the installation of panels;
• Protection of decoration decoration.

It is noteworthy that imitation of the beam is a universal material, which can be installed not only from the outside, but also inside the premises.

Preparation of tools and materials

In order to carry out work on installing the simulation of the bar, it is necessary to prepare:

• Self-tapping screws;
• Dowels;
• Nails;
• Kleymery;
• Bar or galvanized profile;
• Thermal insulation;
• Waterproofing;
• Screwdriver;
• Protective composition;
• drill.

The bar will be used for the production of a crate, as the elements of which may be made of galvanized profiles. For the external wall you need a waterproofing and a heater. The screwdriver can be replaced with a gun to install the Kleimer. If the house has concrete or brick walls, you will need a drill. For the accuracy of the location of the imitation of the beam, you should also prepare a building level.

Before you will be able to install the simulation of the beam, you need to take care of the selection of panels. For interior lining, the best varieties are A, AB, B, and also extra. As for the external walls, then for this the material, whose width of elements starts from 100 mm, is perfect. If you use a less impressive width, then the finish will be like a lining. As for the interior trim, the width should be reduced to 21 mm.

Simulation of the bar must begin with the preparation of the material. To do this, it should be brought into a dry room. The profile should be installed vertically, the distance between the elements will be a limit of 60 to 80 cm. The beam will cost less, but it will serve much less during operation, because the material has properties to warp and rot. Before starting work, wood materials are treated with an antiseptic.

Even if you have to work with a frame house, you still need to install a crate. It will allow to form an additional air space between the panel and the walls. This eliminates the accumulation of moisture, and an additional air pocket will save heat inside the premises. Among other things, in the hollow space you can hide communications.

Recommendations for work

Mounting the imitation of the beam involves the use of waterproofing, which will protect the heater. If you have to work with a wooden or frame house, then fix the material will be more convenient than screws. To the surfaces of bricks and aerated concrete the lath is fastened with dowels or self-tapping screws.

Wall Preparation

Before starting work, it is important to make sure that the walls are fairly level. Preliminarily they are covered with plaster or sheathed with sheet materials. The walls of a wooden house are usually not leveled, and when installing a lath to fasten the elements, you still need to take into account the vertical. On the aligned walls should be strengthened with a stapler waterproofing, it is installed with an overlap of between 30 and 40 cm.

Installing the burr

If you are attracted by the appearance of imitation of the bar, the installation of this material with your own hands can be fully implemented. At the next stage you need to start fixing the crate. To proceed with these manipulations is necessary, moving from the corner of the house. The pitch of the trolley should be chosen taking into account not only the width of the imitation of the timber, but also the dimensions of the insulation.

To reinforce the elements of the lath from the timber to the brick wall, you must first attach the material by drilling through the hole. Further, the dowel is driven in and the lath is screwed. With wooden walls it is much easier to work. For them, self-tapping screws are used, which are selected taking into account the thickness of the bar. However, this parameter should not be less than 30 mm.

If you will be installing the simulation of the beam, the instructions given in the article should help you in this. The next step is laying the insulation, which is usually a foam or mineral wool. For indoor use this stage is not needed. Thermal insulation is located between profiles or beams, and on top is closed with a waterproofing film.

Simulation of the bar

In order to extend the life of the imitation bar, it must be treated with an antiseptic. Fasten the panels, moving upwards from the bottom. The first panel should be laid down by level. From the bottom of the house should retreat about 15 cm.

The installation can be carried out in one of several ways, the first involves the use of self-tapping screws, while the second involves the use of nails. There is another technology, which is accompanied by the installation and fastening of the clamps. Using self-tapping screws, you can install them at an angle of 45 °. An alternative solution is screwing the screws into the top of the panel. Nails can be installed in the groove.

Mounting the clamps will be the simplest task, but this system will not be highly reliable. You can use this method only if the material is thinner than 21 mm. Using fasteners in the form of thin nails, you can not guarantee that the panels will not loosen over time. That's why for the external skin experts recommend using self-tapping screws.

Installation of fasteners in the front surface of the elements involves pre-drilling holes for self-tapping screws. Their diameter should be larger than the self-tapping screw. After installing the fasteners, a wooden cork is inserted, which is pretreated with PVA glue. After that, the surface can be sanded.

Cost of installation of imitation of a bar

If you are not sure that you will be able to independently install the imitation of the timber, the price for these services should be known to you. For 1 m ² installation outside the building will have to pay 750 rubles. Interior decoration will be more expensive - 800 rub. Per square meter. If you have to trim the attic, then for the services of an external installation of imitation, you will pay 950 rubles. Per square meter, while the work inside will cost a little cheaper - 900 rubles.

Installation of imitation of a beam inside the house: preparation of walls

The installation of imitation of the bar inside also involves preparation. For this, the surface of the walls is cleaned of dust and dirt. On the base it is necessary to strengthen the vapor barrier by the type of pergaline, then you can proceed to the installation of the crate. In this case, the distance between the elements will be a limit of 50 to 70 cm. On the concrete and brick walls, the lath is strengthened with dowels, whereas when working with wooden walls, self-tapping screws can be used. The bar is treated with antiseptics, and for damp areas, a galvanized profile should be used.

Installing the panels

For some, the cost of installing the imitation bar is too high, at this point they decide to do the work themselves. Installation is carried out horizontally, and the fixing method is like the facade finish.

Use for this purpose is most convenient klyaymery, but when working with the ceiling manipulation will be more complicated. In this case it is better to use self-tapping screws or small nails. Install them in a spike at an angle of 45 °. The facial method for the premises is better not to use, because a small thickness to hide behind the hats will be difficult, which will spoil the appearance of the walls.

Conclusion

The installation of imitation of the beam inside the house will also presuppose decorating the corners, for this special internal and external elements are used. They are purchased with the panels. But between the walls and the ceiling should be installed baguettes. For the lower part of the room you need to buy a skirting board. Once you have completed the finish, you can sand it and apply a varnish to the surface. In some cases, toning is performed, but this approach is "on the fan". The ceiling is best to install already painted panels, this will save time and effort.