Installation of PVC wall panels with your own hands. Economical repair

Plastic panels - inexpensive material used for finishing both residential and business premises. This type of wall and ceiling cladding is inexpensive, while the decorative qualities are very good. Among other things, the merits of this material can be attributed to the ease of installation. It is not difficult for anyone to install PVC panels by oneself.

Which material to choose

Before embarking on such an operation as installing PVC wall panels with your own hands, you should determine the actual type of material. For the decoration of premises for different purposes, plastic elements of several types can be used from the inside:

• PVC lining. This material looks similar to its wooden analog - it has a small width and often corresponds to the coloring.

• Sheet panels. This variety is similar to the sheets of decorative plywood.

• Conventional panels in the form of a plastic "board" with a stud / groove.

When choosing a particular type of material, you should first of all focus on the specifics and design features of a particular room. Plastic lining has the advantage that it does not "heavier" the room and gives it some kind of natural look. Sheet panels are usually used for finishing walls and ceilings of large areas. A very good solution, for example, may be the sheathing of the attic or the basement of the country house. Versatility is one of the main advantages of a material such as a wall panel. For the kitchen, PVC is just perfect, just like for a bathroom, living room, hallway, etc.

Cost of PVC panels

Plastic elements of this variety are not without reason considered a budget option for finishing. Very low cost is one of the main advantages of such material as PVC panels. The price for them fluctuates between 200-300 rubles per lamella in the form of a "board". The width of the plastic decorative element is usually 25-30 cm. Thus, for finishing, for example, walls with a length of five meters will have to spend only about 4-6 thousand rubles. If desired, you can find PVC panels and cheaper - for 100-150 rubles. However, they are unlikely to be too beautiful and original design.

What tools will you need?

The installation of PVC wall panels is carried out by hand on a special frame. To install it you will need a drill, a building level, a tape measure. The panels themselves during the installation usually have to be cut. Therefore, you will also need to prepare a hacksaw for wood or a jig saw. In the event that it is supposed to make additional warming of the premises, you will have to buy a trowel for applying glue and a construction stapler.

Carcass beams

In addition to the panels themselves, you will need to buy a wooden beam before beginning the plating . The weight of decorative PVC finishing is insignificant. Therefore, it is not necessary to purchase a bar too large. It will be sufficient to have a variant of 3x3 cm or 4x2.5 cm. The only exception is when the walls are additionally insulated. Insulator plates are installed between the frame elements. Therefore, the beam for this type of skin should be chosen with a cross-section corresponding to the thickness of the insulation. Also, you will need to purchase glue for boards, dowel-mushrooms, primer and vapor barrier film.

Other types of carcass

PVC wall panels for the bathroom are usually mounted not on the cobblestones, but on the metal frame. Wooden in the bathroom, sauna or bath can simply "story". Recently, a plastic thin skeleton is often used under PVC panels. Its use allows you to save a few centimeters of the area of the room. However, it is recommended to use this option only in rooms with very even walls.

Assembling the frame

Elements of the base under the panels can be installed horizontally or vertically. Everything depends on the direction in which the PVC-paneled walls will be finished. Fastened beam or profile by level. Preliminary in the wall are drilled holes for dowels. Since the joint between the panels and the ceiling is usually closed with a decorative plastic skirting board , the beam or profile in this place must be installed necessarily. The same applies to the corners of the room. Angled strips are mounted here.

When installing the frame, it is important to follow exactly not only the verticality or horizontality of the elements. It is also necessary to ensure that all the beams are in the same plane. PVC panels - the material is elastic. However, the distortions will give the wall a less than neat appearance. Correct position of the beams in the right places can be done with small wooden wedges.

Before installing the frame, you should think about where in the future will hang heavy hanging cabinets, shelves, pictures and so on. In these places it is necessary to fill in additional horizontal bars.

Installation of PVC wall panels with own hands

In case of the need for insulation between the elements of the installed frame, the plates of expanded polystyrene are fixed to the glue beforehand. In addition, they are attached with special "fungi". Then the vapor barrier film is stretched onto the frame.

Actually, the very inner wall paneling begins with a corner. Here you set the starting bar. In its groove insert the comb of the first panel. To the frame, lamellae are fixed with special staples using a stapler. Next, the second panel is inserted into the first one and is also fixed. The last lamella on the wall is inserted into the previously fixed finish strip. If the width of the PVC element is too large, it can be cut off, but not more than 1/3.

After all the walls have been paneled, they begin to decorate the space above the doors and windows. At the final stage set the upper decorative skirting.

Useful recommendations

Installation of PVC wall panels by one's own hands must be carried out with the following recommendations:

• The frame can be mounted on uneven or even unfinished walls. This will save on finishing.

• The bars should be attached to the wall only using galvanized self-tapping screws or dowels.

• The first element of the skin must be aligned as carefully as possible. Otherwise, all panels will be set crookedly.

• If the interior decoration of the walls of the premises is carried out in the summer period of time, the panels before installation are kept at room temperature for a minimum of 12 hours. When performing the same installation in winter, this period is increased to 2 days (if the panels were stored in frost).

• Unpack the lamellas as carefully as possible. This material is not too resistant to various kinds of mechanical damage. Pull out the plastic elements carefully at the edge and only one by one.

• Hacksaw for cutting plastic should be used with small denticles.

As you can see, the installation of such material as PVC panels, the price of which is low, is a very simple procedure. The main thing in the performance of this work is to set the frame exactly. The lamellas themselves should be adjusted to each other as tightly as possible. In this case, the skin will be neat and durable, and the design of the room is cozy and attractive.