How to make a tent with your own hands

It is not always possible to install a full-fledged gazebo on the territory of the countryside. In this case, a place for rest can be equipped with a tent, which will be an excellent alternative to a gazebo. If you are thinking about how to make a tent with your own hands, then it is worth considering the technology of work. As the main advantage of the tent can be identified that at any time it can be moved to another place, if necessary, by placing it in any convenient point of the territory. The tent can be manufactured quickly enough. And if the design turns out to be lightweight, it can be taken even for a picnic.

Preparatory work

Before you make a tent with your own hands, you need to choose the fabric and place on the site. When planning a tent, you need to think about its location. It should be an open area, which is distinguished by a flat surface. The chosen territory should be cleared of a fertile layer of soil, stones and all kinds of garbage. The substrate must be leveled, then carefully compacted. If you intend to build not a stationary, but a light portable structure, then it will be enough to mark out the territory and make grooves for the installation of pillars. If the tent with its own hands will be manufactured on the principle of a stationary structure, it will be necessary to erect a foundation, as well as lay out the flooring.

Carrying out excavation works

If it is supposed to erect a foundation, then for this on the selected territory it is necessary to remove a layer of soil, having deepened by 10 cm. The bottom and walls must be carefully leveled, then the prepared place should be filled with sand, which must be poured with water and well sealed. On the basis prepared in this way it will be necessary to lay the sidewalk tile, as a basis it is possible to choose a wooden flooring.

Options for the manufacture of tents

In order to build the most simple tent with your own hands, you will need to use a bar, the height of which is 2.7 and 2.4 meters, the cross section of these elements should be 50 x 50 mm. You will also need wooden boards, the thickness of which is 40 mm. In order to perform a canopy and walls, you need to prepare the fabric. When carrying out work, there is no way to do without steel corners and screws.

After the territory is marked, it is necessary to excavate the pits to install the support posts, and then install them. Use for digging pits, you can rotate, the depth of pits should be equal to 0.5 m. After the supports are installed, they need to be covered with a layer of soil.

Features of the tent assembly

The tent with its own hands must be made in compliance with the requirements of strength and durability. Before proceeding with the work, it is possible to protect all wooden elements from decay, covering them with a primer or paint, as well as antiseptic compounds. In order to ensure the free flow of water, you need to equip a pitched roof. To do this, the front support posts should be set 30 cm higher than the rear posts. After the solution has completely solidified, horizontal supports must be fixed between the supports, and the mating must be done by using steel corners. So, the frame is ready. Making the tent with your own hands, you only need to cut it out of the fabric, and then sew the roof cover, prepare the curtains to form the side walls. The roof can be made not from a fabric, but from a polycarbonate. At the same time, rafters must be placed on top of the crossbeams, which must be made of a bar. Choose material with a cross section of 50 x 50 mm. On the rafters, the crate must be mounted and reinforced, on which the covering material is fixed, then use self-tapping screws.

Features of the manufacture of a steel tent-tent

The marquee for the wedding can be made by the type of a pergola. In order to install such a construction, it will be necessary to place the support posts on the chosen site, and also to fix the concrete disks in the amount of 4 pieces, they can be replaced with plates, in the central part of which an opening is made. They will act as the foundation of the tent. In the holes of the disks it will be necessary to mount steel bars, which are sometimes replaced by plastic tubes. The upper ends of these rods must be connected together by means of clamps or wire, while the task is to create supports made in the type of arcs.

After you can mount the frame, the upper edge of the tissue should be collected, and then fixed. It will need to be reattached with a twine or wire, it should be done in the places where the carcass arches are connected. After the fabric can be straightened and stretched along the rods. Making a wedding tent with your own hands on such a technology, you should avoid slipping the fabric, you can do this by using strings that are sewn on the inside of the structure.

Children's tent and its manufacturing features

In order to build a similar tent, you will need to use a plastic hoop, the diameter of which is 88 cm, you need a plashevka or cotton fabric. The width of the base of the lower cone will be equivalent to 50 cm, whereas the length of the element will depend on the height of the structure. Between them you need to connect the cone-shaped elements of the parts, the whole design can be collected with the help of ribbons in a quantity of six pieces, they can be placed at the same distance along the edge, and then tied to the hoop.

Making such tent for giving by own hands, from a fabric it is necessary to find out identical details which will make the bottom part of a design. You will need to prepare the same number of elements for the upper tent area. In order to strengthen the tent, it must be hung to the branches, for convenience of use the dome should be equipped with a ring. To perform the frill you need to prepare a strip, the width of which is 20 cm. It must be folded in half and outline the dimensions of the semicircles. On the contours it is necessary to stitch the assembly, and after getting rid of excess quantity of fabric and turn the strip on the front side.

Finally

Carrying out the tent for the dacha with your own hands, the ring can be made of a fabric, the size of which is 30 x 10 cm. This element also needs to be folded along, and after stitching and pulling. To fix such a ring on the structure it will be necessary to prepare 4 cones, between which a loop is inserted and everything is spread. The tent-tent with own hands can be made quite simply according to the technology described above.