How to glue the film on the phone (photo)

Every mobile device, whether it's a smartphone or a tablet, today has a large touch screen. You can control this gadget, of course, only by touching it on that screen. And this, in turn, causes pollution of an ideally clean display surface, the emergence of cloudy spots, traces of oil, and so on. And this is not to mention the banal possibility to pollute the display due to external factors.

The only solution that can help all of us in working with devices is a protective accessory - a film. We are going to tell you how to correctly apply the film to the phone and the tablet in this article.

Why glue the film?

In addition to protecting the screen from dirt, dust and fingerprints, there is also a function to protect the display device from mechanical damage. And this, believe me, is much more serious.

After all, in real life it is impossible to provide 100 per cent ideal conditions for the operation of the phone or tablet - there can always be a situation when an item touching the screen will leave a scratch or scrub. Obviously, the appearance of the gadget will suffer from this, not to mention the performance (and image transfer).

If you know how to properly apply a protective film to your phone, and do it in a timely manner, you should not worry about your device. You simply remove the old film in the event that its appearance stops you arranging, and replace it with a new one. Thus, the screen itself of the tablet or smartphone will remain unharmed.

Without a film, it is obviously possible to get rid of scratches only after the screen has been replaced.

How are the films arranged?

Having understood the benefit of a protective film, you should pay attention to how it is arranged. So, if you take one such film in hand, you will see that it has two labels. On the first one it can be indicated that this is the protective layer number one; On the second, respectively, "layer number 2".

All true - modern films are delivered to the market with three layers. If you imagine them in the form of a sandwich with two slices of bread and sausage inside, then the actual "film" (sausage) is the real film that will protect your screen. The last layer - "bread" - will be removed during the installation process. They serve to protect the film itself from damage (both from the top and from the bottom side). If you want to know how to properly apply the film to your phone, remember to remove them.

Preparing the screen

The guarantee that the film will reliably hold in the course of using the device is not only its condition and quality. In fact, an important role here also plays a surface on which the film will be glued. In this case, we mean the screen of a phone or tablet.

In order to keep the film, from the surface of the display you need to remove all unnecessary: dust, mote, fingerprints, moisture. If anything remains, in the future the appearance of the gadget's screen will be a bit messed up.

Again, if you want to know how to properly apply the film to the phone "iPhone 3q" (as well as on any other model), do not forget to clean the display. You can do this with a soft napkin or cloth, which does not leave villi.

It's simple: rub the screen and look at it at an angle to determine if anything is left on it or not. Ideally, the display surface should look smooth and smooth. Then, even after the protective layer of the film is glued, the screen will look great.

First step

So, after cleaning the display first thing is to try the edges of the film to the border of the screen itself. According to the instructions on how to correctly apply the film to the phone "Fly 4403" (and not only to it), the gap between it and the display border should be approximately 0.5 millimeter.

This does not mean that you need to equip yourself with a ruler and measure the same distance - no. You just need to "eyeball" to estimate that from the film there was a small gap. This is normal, because the films produce in slightly smaller sizes than the screen, so that they lie more evenly.

After you have outlined the "beginning" - the line from which you will glue the film, it is necessary to proceed to its further gluing. You need to do this gradually, slowly. However, read more about this.

We put the film on the device

As you already understood, if you do not know how to properly apply the film to your phone, start with a clear line, then move gradually to the opposite edge of the device. As experts say, you need to act on the narrower side of your gadget. So it will be easier to glue the film with an even "front".

Next, you need to apply tools to level the surface of the already pasted layer of material. In particular, we are talking about a plastic card (although a scraper will do). Pressing it to the surface of the display, covered with a film, you can "drive out" the air bubbles arising there. Thus, the screen will look nice and neat.

Remove the top layer

After you managed to cover the screen of the device with a film, we proceed to further actions, namely - remove its upper protective layer. This is done simply: you need to pull the label left on the film, which says "Layer number 2" or "Remove after gluing" (depending on the type of film). Do this gradually and carefully.

If you have learned how to correctly apply a protective film to your phone (Gerffins or any other brand), after removing the top film, you should have a perfectly smooth coating protecting the display device. Actually, after that you can start using your gadget.

Possible problems

An unpleasant situation can arise if you, even though you have read, how correctly to put the film on the phone, but did not do it properly. For example, this applies to uneven gluing of the film or air bubbles left on the screen.

In the first case, you can simply re-paste your film. It takes a little time, and if you do it right, the accessory itself will not deteriorate, it can be used again.

Another problem is the bubbles that will make your screen ugly. You can deal with them in several ways. The first one we already described earlier - arm yourself with a scraper or plastic card and just "squeeze" them to the nearest edge of the device. This will help to overcome the big bubbles. As for the little ones, most of them, as practice shows, can disappear themselves. So do not be discouraged if you notice a couple of them. The main thing is that they should not be caused by any kind of mote falling between the glass and the film.

The place where the film is glued

In addition to recommendations on how to correctly stick the film on the phone (photo - also a visual material), I would also like to give advice on the place suitable for gluing.

As already noted above, it is necessary to exclude the possibility of dirt, dust, hairs and other objects getting onto the glass of the device. This means that it is not possible to film the film qualitatively in dirty, dusty rooms normally. The same applies to open space - the wind can spoil everything.

We recommend choosing a room where it is clean and windless. If we talk about an ordinary apartment, then the best for these purposes is a bathroom, for example. Because of the high humidity of the dust there is less.

Go to such a room and glue your film. Let's hope you succeed!