Boiler: how to install your own hands. Step-by-step instructions, recommendations

Today, an electric heater and a boiler are in great demand. How to install such equipment will be described in this article. With the help of such a device you can cope with the problems of switching off hot water. Among other things, such installations can operate on an ongoing basis. In a wide range of modern stores you can find accumulating or flowing electric boilers, the latter of which are in less demand, because they are inferior to storage by volume and profitability. To install such a device you can use the services of specialists or to cope with the work yourself, but you will need to follow all safety rules. To do this, the electricity is completely cut off, and the hot water pipes overlap.

Preparation of materials

If you decide to buy a boiler, how to install such equipment, you should know in advance. Of course, independent work is cheaper. If you refuse the services of professionals, you should prepare a certain set of materials for installation. You will need a plumbing liner or sealing tape, a safety valve, two flexible water hoses, and two dowel-nails. When buying a water hose, you should consider that you need two elements, each of which is 2 m in length. However, the length will depend on the distance to the tie into the water pipe system. When buying dowels-nails, it should be noted that at their ends should be hooks. By the way, about the safety valve. It should be mentioned that it is supplied complete with an electric boiler. The valve must have a diameter of 10 mm.

Preparation of tools

So, you need a boiler. How to install such equipment, you must find out before it is acquired. Do you want to install yourself? Good luck! However, it should be taken into account that in some cases the manufacturer's warranty will be canceled if the works are carried out independently. In addition to materials, it is necessary to prepare certain tools, among them: screwdrivers, drill bits with a winning tip for fastening to a brick wall, a wrench and a punch. The latter can be replaced by an electric drill.

Installation Instructions

Many home craftsmen, knowing how much it costs to install a boiler, prefer to do all the work themselves. It is not surprising, given that such services cost about 5000 rubles. There are skills and you know which side to go to the puncher and how to hold a screwdriver? Then why overpay? But if you do it yourself, you will have to prepare properly. Not the least role here is played by the testimonies of those people who are not engaged in such a thing. If you study all the recommendations, you can come to the next.

The process should begin with choosing the location for attachment in the bathroom or bathroom. Most often such equipment is installed above the toilet, where it will not interfere with anyone. It is necessary to check the strength of the wall, since it will have to undergo loading from the boiler. If the room is not reinforced partitions of gypsum board, then from installation of the unit on them it is worth to refrain. With a boiler capacity of 50 liters and more, a double load, ie 100 kg, will be placed on the wall.

Before installing the boiler in the apartment, you should determine the bottom point of the equipment location, marking it on the wall surface. Next, the master measures the distance from the fastening bar to the lowest point. The first is firmly welded to the body of the equipment. The distance should be noted on the wall. The next step is to drill two holes. Masters emphasize that you need to remember that the fastening bar of such holes does not have, anchors with a hook at the end must cling to its edge.

Recommendations for work

So, everything is ready to mount a boiler on the wall. How to install it correctly? The question is by no means idle: the design must be secured reliably, for the fall of such a massive device can cause injuries. If the wall is made of concrete or brick, then for the master's work it is recommended to use a perforator with a winning drill. A wooden drill is used for a wooden wall, the diameter of which is smaller than that of a plastic dowel. The latter must be installed in the hole and, if necessary, driven. The metal anchor is screwed in until it stops turning. As a rule, a depth of 12 cm is enough. The boiler should be hung by hooking the hooks of the anchors behind the bar, for fixing on the body of the unit. On this process, the suspension of equipment can be considered complete. As you can see, the technology is not very complicated, so any home master can overpower it. At the next stage, it is possible to connect the boiler to the water supply system, for this you should use flexible hoses.

Connect it!

Judging by the feedback, instead of flexible hoses, polypropylene pipes can be used, but it will cost more and take longer. At the bottom of the boiler there are two tubes, one of which has a blue plastic ring. Cold water will flow through it. The second tube is marked in red and is intended for hot water outlet.

According to the craftsmen, a safety valve should be installed in the place where cold water is supplied. It is usually supplied as an accessory or as an option. The first step is the connection of the safety valve. Do not forget to wind the sanitary flax or the sealing tape on the thread.

Masters are advised in the next stage to screw one end of the flexible hose to the safety valve. In this case, it is necessary to abandon the use of the tape, since there is a rubber gasket in the hose nut that acts as a sealant. Well, the question of how to install a boiler in the apartment is almost solved. The next step will be the fastening of one end of the flexible hose to the pipe from which the hot coolant enters. This sealing tape is also not required.

Now you can do the connection of the free ends of the hoses. The end, to which cold water will flow, should be connected to a water pipe. At this point, a valve or a faucet must first be installed, which, if necessary, will shut off the supply of liquid. Do not neglect this recommendation, as the boiler may fail during operation or require replacement of parts. The free end of the other hose must be connected to the pipe that goes to the mixer.

Advice of specialists

In principle, it is not difficult to install a water boiler by yourself. You just need to equip yourself with certain knowledge (in addition to tools and materials). There are a lot of nuances in this matter. In particular, before connecting the unit, it is necessary to remove the tees on the water pipes. In the absence of certain experience, it is better to entrust this work to professionals. Now you can do the electrical part. In the case of Thermex water heaters, they have one feature, which is the presence of a cable for connection with the plug in the kit. Moreover, this element is connected to a boiler. If this is not the case, then the consumables will have to be purchased separately.

And further. To all went without a hitch without a hitch (read - without accidents), the master is strongly advised to observe safety when working with electricity.

What else must be considered when carrying out work

If you are faced with the question of how to properly install a boiler, then you should know that the cover does not have to be opened if everything is already connected in the equipment. It is enough to install a socket with grounding in advance, which should be near the equipment. Turn on the cold water tap to check how tightly and securely the connection is. If there is no leakage, the boiler plug may be plugged into the outlet. Now you know how to install a boiler by yourself. If you did everything correctly, then the indicator should light on the case. After this, you can set a certain temperature by using the knob, which is usually at the bottom.

Conclusion

It is important to remember the main errors that are allowed when connecting the equipment described in the article. In particular, before installing a boiler in the bathroom, the masters recommend taking care of the availability of a hot water supply system with circulation. This will minimize energy losses if hot water is constantly present in the pipes.