Washing "Vince". Advantages and disadvantages of Wynn's cleaner

Probably, the majority of Russian motorists at least once faced with the need to flush the engine injectors and clean the fuel system of the car. Very often such a problem becomes urgent during the melting of snow. At this time, the operation of the car becomes particularly difficult. Let's see why there is a need for washing and whether it is possible to perform the procedure on your own. Also, many are interested in the question of whether there are funds after which there will be a guaranteed result. Many argue that the washing by Vince is very effective. Let's see if this product is so effective.

Why do I need to periodically flush the injector?

In the composition of any brands of domestic fuel is, besides the fuel itself, also a lot of various additives and impurities. Due to benzene, olefin, water and sulfur, gasoline producers are trying to increase the octane number. Also very often it contains gas condensate. This fuel harms the fuel system and the engine of the car. All harmful impurities during the operation of the car accumulate inside, as well as outside the injector and in the fuel channels in the engine.

When to flush the injector?

Any car owner in terms of how the engine behaves will be able to determine the need for cleaning the injector. Often, the following signs indicate the need for service:

• Significantly reduces the power of the power unit.
• The car starts badly, which is especially noticeable in the winter.
• The motor becomes uneven and unstable. This is best seen at idle and transient regimes.

Also, the car is slower to gain speed, the level of toxicity of exhaust gases is increasing. "On the hot" there are dips and detonations. If several of these signs are observed during the operation of the vehicle, this means that the injector is urgently needed for washing.

Wynn's auto chemistry: why motorists choose these products

The modern market offers a lot of different cleaning agents for the fuel system of the car, including the injector and injectors. But not all of them are equally effective. The car owners tried all the options offered. Now there are two that really work. This is expensive Japanese products, as well as flushing "Vince" - it is much cheaper, and the quality is the same. The products are produced in Belgium. The company has been operating in the world market of auto chemicals for more than 5 years. The main advantage of the Belgian brand products in front of various import and domestic competitors is a number of strong solvents in the composition. Due to the fact that Wynns is a washing created on the basis of competent selected components, it starts actively dissolving solid layers of deposits of different thickness from the first minute of application of the product. This is a big plus.

Wynn's Wash Properties

Washing "Vince" very qualitatively cleans not only the injector, but also other nodes. The product effectively cope with valve seats, piston parts. Suitable for processing rings and pistons, cylinders. Do not disassemble the motor. The Belgian cleaner for injectors and injectors helps to restore the characteristics of the spraying sprays of the mixture and the optimum periods of its intake. The liquid is practically ideal for washing out the deposits and accumulations of the exhaust valves and prevents their sticking. Washing "Vince" allows you to eliminate detonation when the engine is running and makes it easier to start the power unit. The manufacturer claims a significant reduction in fuel consumption.

All this makes Wynn's products the leader in terms of sales practically in all countries of the world. In the range of liquids there are products for both gasoline engines and diesel engines. These cleaning flushes are suitable for independent use on all models of injection vehicles. This has been proven by millions of car owners around the world.

How do I clean the injector with a Vince liquid myself? Preparation

Washing "Vince" - a very simple procedure. To prevent the engine, you need to access the problematic part of the unit. It is best to perform work on the algorithm that the manufacturer suggests in the instructions.

So, you need to start the car engine. Then remove the fuse that is responsible for the functioning of the gasoline pump. This is necessary in order to lower the pressure from the fuel system. After that it is necessary to remove the terminals from the injectors and the hoses for fuel supply. Then carefully dismantle the ramp with injectors and o-rings. Now there is free access to the injector. Now it is worth considering how the flushing of the nozzles "Vince". The principle is not to allow the fuel injector to flow liquid when the valve is closed, and vice versa.

For cleaning, use a "Vince" liquid, as well as a special device that helps to purge the liquid through the fuel injector. As this device is suitable ordinary plastic bottle. It is connected to the container in which the liquid is located. Then the bottle is also connected to the inlet on the nozzle. As a result, a convenient device is obtained, with which the cleaning of the injector will take a minimum of time.

Washing process

Now you can proceed with the cleaning operation. The liquid is passed through the nozzle - for this, the valve is periodically opened and closed. This procedure should be repeated until spraying is necessary. If this does not happen after cleaning, then the part has failed. Next, the cleaning is performed again.

If layers of sediments are visible inside the injectors and on the surface of the injector walls, then Wynns (rinsing) must remain inside the injector for a while. This is the only way to clean the injector as high as possible. Stop work is only when the valve seat on the valve is perfectly clean, and with it the injector holes. At the end of the procedure, all the parts are assembled in the reverse order. This completes the cleaning of the injector. The results will be visible after a while. The engine will start to work more stable, fuel consumption will decrease.

Diesel engines

Suffer from poor-quality fuel and these engines. Like gasoline, diesel also contains various substances that do not have the best effect on the state of the fuel system. The nozzle is also subjected to high temperature loads during operation. She works under great pressure. If we add to this the quality of fuel with an increased percentage of heavy fractions, then we can say that the washing of diesel injectors should be carried out even more often than the maintenance of gasoline. So, during the work of the engine, as well as on a hot, but already idle engine, on the surface of the fuel injectors, the fuel remains are converted into resinous deposits. Sometimes there is a deposit. Gradually, these layers become thicker and thicker. Over time, the injector and does not stop spraying the fuel into the combustion chamber. Because of this, the normal operation of the motor is disrupted.

When to process?

Flushing diesel injection nozzles is necessary when:

• The engine gets worse.
• At idle turns there are interruptions.
• On partial loads there are knocks.
• In the intake tract there are different sounds - more often clapping or sneezing.

Also, the need for cleaning is indicated by dips during a sharp set of revolutions. In general, the signs are the same as with gasoline engines.

Wynn's for diesel engines

The Belgian manufacturer of auto chemistry has not forgotten about the owners of diesel engines. For them, too, there is such a tool. According to reviews, it is quite effective. The very washing of the diesel is done a little differently. The liquid is poured into a container, where the fuel supply hose is then lowered. Reversible fitting is lowered there too. Then the engine starts. It is necessary for the engine to work with this device for 30 minutes. After the time has elapsed, you will notice that the liquid has become darker. By the end of the process, the agent will be almost black.

When the "Vinsom" flushing of the diesel engine is already completed, the engine should be run on clean fuel. At this point, the cleaner and leavings are washed out of the system. Then the hoses can be connected back.

Conclusion

So, we figured out how to clean the injectors yourself. системах питания. "Vince" - this is an excellent tool for removing deposits in the injector power systems. This product can be purchased both in the market and in specialized stores. старания не принесут результат. The main thing is not to buy counterfeit goods, otherwise efforts will not bring the result.