Vinyl laminate: customer testimonials, advantages and disadvantages

A large number of different materials for decoration can allow to realize the most different fantasies of owners of their own dwellings and numerous professional designers. With their help you can turn your apartment or house into a real work of art. Since any finish should be performed at the proper level and is intended to add beauty facilities, then it is necessary to approach the choice of materials with full responsibility. And among the most popular materials can be identified vinyl laminate, reviews of which only the most positive.

Coverage is a separate strip, which consists of several parts - the top and bottom. In the first case, it is a layer of protection. With its help it turns out to make so that the laminate imitates a variety of natural materials, such as wood, stone, etc. Such material is popular because it has a lot of positive characteristics. Strength, wear resistance, resistance to shocks of a mechanical type and the same damage are only a small part of the advantages that, for example, quartz-vinyl laminate possesses. All this must be taken into account if there is a desire to make a beautiful and durable floor.

What varieties are on sale?

1. Vinyl laminate is self-adhesive. Reviews about him the most favorable. The material can take the form of a square or a rectangle of different sizes. The lower adhesive part is closed with a special paper protection. It is necessary to glue such a laminate completely.
2. Vinyl lock laminate, which has an adhesive tape. Completely glue to any specific surface is not required. The main thing is to connect the bars to each other.
3. Roll vinyl laminate. The opinions of professionals say that it must be completely glued to the surface, using specialized glue solutions.

From the chosen type of laminate will completely depend on the main characteristics of this material. In addition, do not forget about the beauty that they carry in themselves.

Categories on which a laminate can be divided

1. Domestic. Used in those rooms where people do not go very often. This is due to a very thin layer of protection. Durability of the material reaches an average of 6 years.
2. Commercial. Fits in those rooms, which are characterized by high traffic. The protective layer is thick enough. Durability reaches 10 years.
3. Special laminate. Used in those rooms in which the floor can be subjected to a variety of mechanical loads. Thanks to special additives, a factor such as slip was significantly reduced. Fits in the shops or in the gyms. To serve such a vinyl laminate, reviews about which are very good, can be up to 15 years.

Household laminate is the most optimal floor covering, which can be laid in living quarters.

What are the advantages of the coating?

The laminate is characterized by high strength and durability. In addition, it is characterized by high resistance to a variety of scratches and shocks. Nor can it be said that it is capable of cracking and crumbling. In addition, it can withstand huge loads.

Due to its excellent moisture resistance it is possible to use it in those rooms for which high humidity is characteristic. Eco-friendliness, simplicity in packing, saving both monetary and physical resources - all this can be safely attributed to the positive aspects that are characteristic of the laminate. Well and separately it is necessary to note delightful aesthetic qualities thanks to which about a covering it is possible to tell that it beautiful and refined.

What disadvantages does the coating have?

However, there are drawbacks. Especially if we talk about vinyl laminate castle. Comments and comments from professionals must be taken into account in order to know about all the negative aspects.

1. When laying it should be borne in mind that the unevenness of the main floor should not be more than three millimeters.
2. The locking type of fastening can be damaged by inaccurate handling. The usual hammer should not be used.
3. Do not allow liquid to enter the coating. Otherwise, it swells and deforms.
4. The traditional way to cover it is better not to wash. It is enough to use a vacuum cleaner.

How does the coating work?

1. First of all, immediately after buying the laminate should be left for one day in the room in which the styling will take place.
2. In this case, the air temperature in the room should not be less than 18 degrees. It is necessary to ensure that the installation of the panels is not accompanied by temperature changes.
3. Preliminary it is required to prepare carefully the basis under a laminate.
4. As a rough floor, any type of surface can act.
5. If the room uses heated floors, then it must be turned off a few days before the installation. Again, the heating technology can only be switched on after 5 days after the end of the installation.
6. Previously, the floor will need to be well cleaned of all traces of dust and dirt.

Floor preparation work

First of all you will need to buy vinyl laminate. The opinions of professionals should be taken into account when measuring the room. For example, not to buy too much. All niches and numerous ledges should be considered, adding about 10 percent to the stock.

If the main floor of concrete, then it must completely dry, gaining the greatest strength. In the event that the pouring of screeds occurred relatively recently, the laminate will need to be stacked only after 90 days.

The floor of plywood, chipboard or fiberboard should have sufficient strength. In addition, it must be completely leveled and dried. If there are ceramic tiles on the rough floor, you should get rid of all gaps and seams with cement mortar.

Elastic coatings must be carefully fixed to the floor before attaching, for example, quartz-vinyl laminate. The reviews of professionals and ordinary people only confirm this.

Installation of self-adhesive coating

Begin laying either from the center of the room, or from the wall. From the owner of the housing will simply remove the protective layer, which protects the adhesive base of the laminate. After this, it is necessary to press the cover to the rough floor. It is advisable to lay individual slabs "uncontrolled", slightly pruning them with scissors and breaking at the point of incision.

Use of glue solutions

Acquire the right glue, which is recommended by manufacturers of a certain vinyl laminate. Information about the solution can be seen in the instruction, which goes on sale together with the coating. Also in this manual is indicated the way of using the glue.

With a notched trowel, the base should be greased with glue in such a way that it is possible to immediately lay the laminate in two rows. Then on the surface on which there is already glue, it is necessary to put the cover plate and press it. Using a rubber spatula you need to get rid of excess air.

Method of laying a laminate with a lock fastener

Glue will need to lubricate only the edges of the panels. Begin to lay the laminate is necessary from the wall. The first row is mounted in such a way that the spike is located to the wall. It is better to cut it completely so that it does not interfere. Between the wall itself and the panels it will be necessary to leave a not too large gap of 3 mm. In order not to form a straight line from the locking joints, the installation must take place "uncontrolled".

If there is an obstacle that needs to be bypassed during the installation, it will be necessary to pre-prepare a special template, according to which the panels will be trimmed.

When the laying is completed, it is necessary to treat the coating with a special roller, with which it is possible to create a load equal to 80 kg.

Installation of laminate

In this situation, you will need to use a special adhesive solution. Installation of the coating is exactly the same as in the case of laying conventional panels on the adhesive solution. The main difference is that the glue will require absolutely the entire area of the room. Thus it is necessary to make so that under a laminate there was no air.

In some situations, the seams between the laminate panels can be sealed by hot welding. But for this you will need to purchase a special cord, which in color will be exactly the same as the cover itself. After the hot welding has been completed, the vinyl laminate will become completely water resistant.

This completes the laying procedure, and you can admire what a vinyl laminate is. Photo, like the review itself, we hope you will be helped.