Table for circular saw. With our hands we make a table for a circular saw

Circular saw is a convenient and productive tool that is used for construction work. Using this equipment, you have the opportunity to use the qualities of maneuverability, as well as speed. However, when executing cutting large quantities of sawn timber, it is rather difficult to work with this tool. Significantly facilitates the task of the table for a circular saw, you can make it yourself without any difficulties.

Features of the implementation

The design can be based on plywood or board. The tool will need to be installed in the lower part of the tabletop, while the toothed disk should be located in the opening of the desktop. The element used for cutting will extend beyond the rectangular opening.

After the saw is turned on, the disc will rotate, and when the material is fed, it will be sawed. The greatest thickness of the processed material will depend on the dimensions of the disk, as well as the power of the tool. When choosing equipment, you need to take into account the thickness of the countertop, to which the saw will be attached at the bottom.

Features of the choice of "circular"

If you do not already have a circular saw, then it can be purchased, taking into account some characteristics, among which you can identify the power of the equipment. If the tool is supposed to be used in household tasks, then a power of 800 watts will be enough to make a table for a circular saw with your own hands. This indicates that the volume of work will be average.

It is important to pay attention to the depth of the cut, this will determine the maximum thickness of the processed material. Manual saws of semi-professional or professional class, as a rule, have a depth of cut in the range from 40 to 70 mm.

Technology of work

The holes in the surface of the working table must be drilled through the markings through and through. Carry out the marking of the stiffeners, when you are making a circular saw table, you need to implement it before cutting. Fixing of the edges to the table top is done with the help of joinery glue, the elements after the joint must be compressed by stubs. In place, it is necessary to designate the location of the lateral stiffeners, which then need to be sawn and glued in the same way.

Features of work

If you decide to make a circular saw table yourself, the drawings can be prepared by yourself. After gluing the clamp, it should not be removed immediately, the structure should be additionally fixed with the help of self-tapping screws, which are installed in the holes. They need to be prepared from the underside, so that the fastening screws are drowned in the structure. After the glue dries, the stiffeners can be removed from the clamps. On this we can assume that the table top is ready.

Recommendations for work with legs

The table for the circular saw with its own hands should be made using the legs, which must be made of a board of 50x100 millimeters. The height of these elements will be determined by the height of the wizard, as a rule, this parameter is 110 cm. The board needs to be cut along the axis at a slight angle from one side. Next, the workpiece is applied to the table top, so that when installing the legs were several in the spread. The fastening of these elements must be carried out from the outside of the stiffeners, the use of bolts is recommended.

Making a table for a circular saw with your own hands, the photo of which can be considered in advance, you must, in parallel with the attachment of the legs, try to improve the stability of the structure. To do this, you can make a screed, which is made from a bar section of 50x50 mm. The manual circular saw must be installed in the prepared groove on the underside of the work surface. The sole should be fixed to the bolts, and the toothed disc must be installed in the slot. The table can be marked, which will greatly facilitate the implementation of cutting materials.

The very surface of the table for protection against moisture can be covered with varnish, which is applied in several layers. When a circular saw table is made, after applying the first layer, it is absolutely necessary to wait for it to dry completely, only then you can start coating the surface with one more layer. This approach will eliminate the effect of sliding the sawn timber on the working surface.

Turning the saw on and off

Making a table for a circular circular saw with your own hands, you must at the last stage solve one important question. It consists in the task of turning the saw off and on. If the master has enough experience and knowledge in electrical engineering, he can shunt the power button, and after taking out the control buttons on the outer surface of the stiffener, which is located in front. If this scheme is too complicated for you, then it will be enough to remove the key using the wire. But you can turn on and off the saw with a power cord.

Table manufacture in the form of a trolley

If you want to make the table mobile, its upper part can be made in the form of a trolley. As its side walls, which will be located behind and in front, you can use chipboard, its thickness can be equal to 16 millimeters. The legs of the table will be bars, the cross section of which is 50x50 mm. Supports for the wheels of the structure will be represented by boards, the thickness of which is 35 millimeters. In order to increase the quality of the table's rigidity, the rear and front walls need to be reinforced with a board having a thickness of 20 millimeters. All parts need to be assembled with self-tapping screws and additionally with PVA glue. The support boards for the wheels must be secured with metal angles.

To fix the trolley on the surface of the table in the supporting boards, it is necessary to make shallow notches, the radius of which will be equal to the radius of the wheel. To attach to the surface of the ladder table, two elements must be installed in the form of inserts, which must be fixed on a single plate. On this, we can assume that the circular saw table has been made by hand and can be used in tandem with the main tool, which at least once was necessary for every home craftsman who loves working with wood.

Finally

If you decide to make a circular saw table yourself (DP 2000) for this technology, then the process will not be accompanied by unnecessary complications. With this is able to cope with any home master, even one that does not have certain skills of doing this kind of work. If you have a desire to significantly expand the functionality of the desktop designed for circular saws, you can increase its security index. You can make the design more complex, it all depends on your skill, and most importantly, the desire to explore new horizons of construction work. Good luck to you and successful new solutions!