Starline: how to enable autorun? Starline alarm system: manual

Starline is a popular brand that manufactures anti-theft systems for various vehicles. When developing protection algorithms, modern innovative technologies are used. Thanks to this, it is possible to provide high reliability of car alarm. Therefore, many domestic drivers install Starline on their car . подробно описывает инструкция. How to enable autorun, describes the instructions in detail. However, drivers are not always clear about this process.

Experienced auto mechanics give advice on how to configure the most basic and necessary functions of this system. When using them, driving will be comfortable and safe.

Manufacturer

The national brand "Starline" today presents to the market of anti-theft systems a variety of signaling options. At their creation the most modern technologies are applied. Thanks to this, high-quality, high-tech signaling of Starline is obtained . интересует водителя в первую очередь. How to turn on autorun, the driver interests first. After all, this function significantly increases the comfort of using the car.

The company "Starline" bases its systems on the advanced achievements of telematics. Thanks to this, it is possible to create a system that is not subject to temperature changes, is fully adapted to the conditions of domestic roads. Also the advantage of the presented product is the low level of interference.

Thanks to such features, the recommended product is recommended for use by large machine-building companies "Chevrolet", "Citroen", "VAZ", "Peugeot", "Opel", etc. Almost for any vehicle, you can choose the appropriate system.

general characteristics

The presented brand today produces many modifications of anti-theft systems. A61. One of the most popular is the Starline A91, B9, as well as the Starline A61. , подробно раскрывает инструкция. How to enable autorun , details the instructions. However, not always the driver can understand the confusing leadership. Therefore, specialists give advice on how to carry out this process.

The equipment of the domestic brand has a two-way car communication channel and a user's keychain. This greatly facilitates the process of setting up and managing the system. The special encoding of the signal completely excludes the possibility of hacking messages. The range of its transmission can reach 1800 m in open terrain.

The dynamic principle is the basis of the signal coding. The driver is notified by means of various sound and vibration signals. About 300 models of cars allow you to install the equipment presented. They can have almost any type of gearbox, as well as diesel, gasoline and turbocharged engine type.

Features of operation

B9. The high quality of the equipment is provided by Starline A91, A61, Starline B9 systems . будет представлено далее. How to enable autorun will be presented later. First of all, it is necessary to determine the basic requirements for the operation of the system. In this case, it will work reliably and fully.

Installation of all elements of the equipment should be performed by experienced specialists. In this case, the probability of making an error is eliminated. An inexperienced installer may violate the manufacturer's requirements. In this case, there is a possibility of incorrect operation of the alarm system, its insufficient security.

Only when all the requirements for installation are fulfilled, the manufacturer gives a guarantee for the uninterrupted operation of the system. In this case, it will be impossible to break the encoding. The signal is transmitted over 128 channels by radio. In this case, the software manages more than 60 teams. The system is operated in the temperature range from -45 to +85 ºС, fully adapted to the unfavorable conditions of domestic roads.

System Management

, необходимо тщательно изучить инструкцию по эксплуатации. When considering the question of how to enable the Starline autorun , you should carefully study the instruction manual. Experts say that the equipment presented is reliable, durable. It rarely fails (under the condition of proper installation and operation), effectively protects the car from hacking.

The system is able to change the settings in accordance with user requirements. This greatly increases the comfort of its application. Settings can be easily changed through the key fobs that come with the equipment. They can have an LCD display or do without it. In the first variant, information exchange between the on-board computer and the user is easier.

The alarm system is Russified, which makes the settings easy. It is very easy to use the key fob. In total, the control unit can store 4 control devices in its memory. Then you can proceed with the settings.

Remote controller

, необходимо разобраться в особенностях применения брелков. When studying the question of how to turn on the Starline motor start-up , it is necessary to understand the features of using key fobs. It is through these consoles that you can set up almost any function of the security system. Best for these purposes is a keychain with a screen. Button-like versions of such settings will be much more difficult. If for some reason, the keychain with the display has failed, it can be purchased at a specialized store and stored in the computer's memory.

This remote has three buttons in addition to the screen. Each of them is responsible for a specific function. The most popular among motorists commands keychain are the inclusion of a security program and autorun. Manage the on-board computer simply, without even being near your car.

The key ring comes with a battery. It is not installed inside the console. First, the battery must be put in the place intended for it. Then the keychain comes on. The user can proceed with the settings.

Buttons

следует начать с управления пультом. Considering how to enable the Starline autorun, you should start by controlling the console. It includes 3 buttons. All settings are performed with their help.

The first control button is responsible for the inclusion of various program commands. It should be pressed 1 time. If the I button is clamped and held in this position, the system will switch (or muffle) the engine. If the motor is on, holding down the I button for 3 seconds will allow the system to enter the guard mode.

Button II is responsible for the cursor that moves around the screen. Its movement is carried out by means of a rapid depression. If the button II is held for a certain time, the trunk latch opens. Button III moves the cursor in the opposite direction. It is responsible for deactivating the keyfob sound signals. If you hold it for a long time, you can program the time indicators, turn on the system's energy saving.

Safety of operation

Before turning on the Starline autorun, it is recommended that you study the safety rules when using the presented security program. All requirements are given in the instructions.

High range of signal can be provided only in open space. Thus the car should be put on the handbrake. Transmission of the manual transmission is neutralized. The automatic gearbox is locked in the parking position.

All machine systems must be fully operational at the time of the settings. The system must have a sufficient amount of lubricant, fuel. If the autostart function is turned on, there should not be any objects in the immediate vicinity of the car. Leave the key chain in a place where children can not reach.

Adding devices to the computer memory

Before activating the autorun, the Starline alarm must be properly configured. If the vehicle that the user purchased has already been in use, be sure to re-record the keychains in the computer's memory. Also, a similar procedure is required if the control unit does not respond to the signals that the user gives from the console.

All available key chains are attached to the system at the same time. First, the driver must muffle the engine. After that, you need to find the Valet system button in the car. About its location says the vehicle manufacturer's instruction. The button needs to be pressed seven times.

After carrying out the submitted manipulations, you can turn on the ignition of the car. The system emits seven beeps. She activated the programming mode. All existing settings are set to the factory position.

Press buttons III and II at the same time. Then the characteristic signal will sound again. This means that the remote control has been added to the computer's memory. The other key chains are attached to the control unit in the same way. The interval between each subsequent action should not exceed 5 seconds. After carrying out such manipulations, the ignition is switched off.

Setting the time

нужно в первую очередь знать, как настроить эту систему. Studying the technology regarding how to enable the Starline autorun in time, you first need to know how to configure this system. To do this, you must use a key fob. It will help you set the real-time parameters of the system. For this, a simple configuration scheme is used.

The third button is pressed on the keyfob. By pressing it, the hour indicator is set. After pressing the button, their designation flashes on the display. With the first button, the number of hours will decrease. The second button can increase their value. Then, for a similar system, you specify the minutes.

Setting up autorun on time

First of all, drivers are interested in how to enable the Starline autorun. You will also need to use the remote control to do this. This program allows you to enhance the comfort of using the system. After a set time period, the program will start the engine. This allows you to warm up the machine according to a certain scheme.

помогут разобраться советы опытных автомехаников. With how to enable the Starline autostart on the timer, will help to understand the advice of experienced auto mechanics. The presented function allows to start the motor with an interval every two, three, four hours, and also once a day. The program can monitor the operation of the motor and turn it on at a distance.

To activate the program, hold the button pressed III keychain. The remote will emit one beep. The button is not released. The cursor must be rearranged to the corresponding screen icon. It looks like a fan blade. Next, the I button is briefly pressed. After 10 seconds the program will be activated.

Automatic temperature start

Also, many users of the system are interested in how to enable the Starline autorun by temperature. In winter, this is a very convenient program. The outside temperature is measured by a special sensor.

The motor can be switched on at -25, -5, -18, -10 ºC. The duration of its operation can be 10 or 5 minutes. Activation of the program occurs by pressing the third button. After the second sound signal, select the third icon in the row. If it is activated successfully, a temperature icon will appear on the clock.

каждый пользователь сможет настроить систему самостоятельно. After considering how to enable the Starline autorun, each user can configure the system themselves.