Sewage pipe 110 mm PVC for the device of individual systems

When creating communication networks for diversion, it is allowed to use conductive elements made of different materials. However, the 110 mm PVC sewer pipe is very popular, as it is ideal for the installation of individual systems. The material used has good performance characteristics, and the diameter provided allows for a normal throughput.

Product Advantages

Using a 110 mm sewer pipe for an autonomous network, it is possible to achieve a quality drainage of domestic sewage from a private house. The systems made of them serve for a long time without additional maintenance. Among the main advantages are:

• Resistance to biological and chemical influences;
• Sufficient strength;
• Low cost;
• Availability of component parts;
• Simple installation method.

During the work, the elements are connected by means of the funnels, which are located at their ends. This option is very convenient. Watertightness of joints is achieved due to special gaskets and hermetic means.

Elements for outdoor use

From the street side, the soil affects the fragments of the waste system. Therefore, 110 mm external sewage pipes are used there. They have a multilayer structure that allows to withstand the pressure of the soil. They can be distinguished from other analogs in orange.

For laying under normal conditions, products marked SN4 are used, the purpose of which is to install outdoor networks with normal loads. Such elements are capable of withstanding ground movements and the impact of low-tonnage transport.

Products for internal use

Indispensable when installing in the premises of sewage pipes PVC 110 mm. The internal method of laying does not require additional mechanical action, so it is not very important to achieve too high strength characteristics during manufacture. Such elements are single-layered and, as a rule, have a gray color.

A set of accessories

The consumer is offered to purchase sewer pipes 110 mm PVC and fittings that allow to connect the conductive fragments with each other. A standard set of additional elements makes it possible to arrange systems of different configurations.

Change the movement of fluid within the pipeline can be done with a special tap. The angle of rotation of this part usually varies within a certain range. The additional elements are connected by means of tees. Peripheral branches of parts are necessary for creating complex sewer networks.

The audit is designed to provide access to the inside of the pipelines. This may be required to carry out treatment activities. If necessary, the plastic cover is easily unscrewed, after which an analysis is made for the presence of blockages in the system.

To combine 110 mm sewer pipes with elements having a different diameter, a reducer is used. However, in most cases, even without installing it. The plug is used to close the holes available at the ends of the pipelines.

To install the bends directly in two planes, special crossings are purchased. The adjoining hole can be located on the left or on the right, so that the conductive elements can be placed in the optimal position before the sanitary devices.

Sealing system at the junctions

In order for the 110 mm PVC sewer pipe to be sealed to the rest of the system, it is necessary to use rubber rings. With the help of such seals, it is possible to provide a reliable seal in the joints. Such gaskets can withstand the effects of many aggressive substances.

Along with its main function, O-rings allow to achieve high resistance to tensile loads occurring during operation due to ground movements along the vertical and horizontal lines.

Storage rules and transportation features

Each 110 mm PVC sewer pipe must be delivered to the work site intact and unharmed. This can be done by observing the basic rules of transportation. If the products will be installed after a while, then it is also necessary to provide acceptable conditions for their storage:

1. The elements should be placed on a flat surface. From the bottom, wooden blocks must be placed every 100 cm. The factory packaging is best removed immediately before the installation work.
2. When transporting products that are not attached to each other, it is required to install additional supports from each side in increments of not more than 200 cm.
3. When manually unloading the pipe, it is recommended to remove it from the machine in a horizontal position. It is not allowed to pull them off at one end. Particular care should be exercised if there is a sub-zero temperature on the street.

Final part

Although a 110 mm PVC sewer pipe is actively used for the installation of individual systems, this does not mean that it can not be used in the construction of networks of industrial and commercial buildings. However, this diameter in this case is suitable only for the organization of internal wiring. For the drainage of waste water out of the structure usually fit elements with a large cross-section, providing better throughput.