How to tie a cord to a cord: proven methods

The main purpose of fishing units is to maximize the performance of their functions related to the high-quality binding of the line to the hook, the linking of the line to the line or braided cord, the reliable attachment of the wobblers or other baits. We suggest to learn how to tie a cord to a cord, a hook to a cord, etc.

Double Uni Knot

This type of fishing knot is the most popular and durable. You can safely say that he is one of the best. It can be mastered by anyone, even a novice fisherman thanks to a simple tying technique. But, despite this, its durability will never fail you. This node can be connected to each other and two lines, and two cords.

So, how to tie the cord to the cord? We take the free ends of the braided cords and add them together. Next, around the cord, which we will tie, the free end of the second cord do 3-4 turns, then pull them together. Now do the same with the loose end of the tied cord around the second. After this we tighten the coils. There should be two nodes: one on each cord. Now it remains only to pull them by the ends in different directions, thereby fixing the formed knot. If the result is too long ends, they should be trimmed. Here's the node and ready.

Counter eight or Flemish knot

There is another method, how to tie the cord to the cord. We are talking about the Flemish knot, which is easy, and most importantly, a reliable way of linking two forests or cords between each other. It can not only be easily tied up, but also checked visually.

So, how to tie such a knot? To begin with, you need to tie a simple knot called a "figure eight" on one cord. The same is done on the other side of the second cord, while starting to knit parallel to the main cord. Eight should be tied so that the two extreme turns are separated from the two cords crossing them and are tightened inward relative to the neighboring ones.

Very important in tying a knot is that, being under load, it should not change its structure. Even if the loop is under tension. If a critical load is assumed, the ropes used should be almost the same diameter, and for safety, the ends should be left long. You can also protect yourself and at each end of the cord around the root end of a double knotted running knot.

Albright Knot

How to tie a cord to a cord? There is another way, besides the above, to bind two cords. Consider the technique of the Albright Knot. So, we unfasten one or two meters of cord with plastic, factory spool. It is necessary to pay attention to the fact that Flyline end or End line should be marked on the necessary end.

Fold in half 5-7 cm cord, hold the left hand (thumb and forefinger) loop. We pass the right hand somewhere about 30 cm of the second cord (backing) in the loop, also clamp the forefinger and the thumb of the left hand. Then, with your right hand, make the free end of the backing 7-12 tight turns directed to the end of the loop from the fingers, grasping the loops of both cords.

The end of the backing, which was left, is looped back, adhering to the opposite direction to the one used at the beginning. As a result, both ends of the second cord should be on one side of the loop.

Now, gently pull the left hand by the two ends of the first cord, before that holding the knot with your right hand, and pull out the excesses of the loop. Then we do the same, changing hands and tightening the second cord on the loop. It is necessary to follow the winding of the second cord (backing), so that it does not fly off the loop. Having done all the previous manipulations, we grip the two ends of the first cord with the fingers of the left hand and strongly pull the second cord to tighten the previously moistened knot.

Surgery unit

For those who want to know how to tie a leash to the cord, we suggest you familiarize yourself with the surgical node, which is for this purpose intended. This method can be called the easiest to link two loops (cords) of the same and different in diameter, and even differing in the material of manufacture. As for the strength of this knot, when properly knotted, it is 100% of the strength of the materials that bind.

The main purpose of the surgical unit on fishing is to attach the leash to the line (cord). Its disadvantage is that the length of the tied lead should be as short as possible. This is due to the fact that the tied end must be completely wrapped around the formed loop, and if it is too long, then it is more likely that all the tackle will be tangled.

So, how to tie the leash to the cord? We take the free end of the main line (cord) and the free end of the leash, add them together. We form a loop from the short end of the main cord and the attached leash, which must be wrapped several times with the folded lead and the free end of the main cord. The number of turns determines the frictional force between the cords, that is, the more turns, the stronger the node is. In addition, with the increase in the number of turns, the dimensions of the node increase. This is seen first of all when tying two thick cords. Therefore, it is recommended to do not more than two or three complete turns.

Node for tying the cord to the spool

How to tie a cord to a spool? This must be done firmly and correctly, regardless of the cord used for winding. Therefore, we tie the necessary knot according to the following technique: we take a spool, wind it with a cord, or lift a forest stalker on a reel; Make a loop, winding the end of the working cord around the main one; Around the base, make three turns, the free end of the cord is wound through the loop, placing next to the base of the formed twist; Tighten the knot, tighten the resulting loop. When pulling, the cord is tightened around the spool. The remaining unnecessary end must be cut off.

Now you know how to tie a cord to a spool. After self-binding the cord to the spool, you will see that this procedure is absolutely not complicated. It is much more difficult to calculate the amount of backing for winding, which is necessary. But that is another story.

Nail Knot Node

How to tie an underbrush to a cord? To tie a knot Nail knot, you need to use a special tool or you can replace it with a small tube, for example, like a rod from a ballpoint pen.

So, grip the left and right fingers of the left hand, the cord, and the end (thick) of the undergrowth, on the right, so that there remains a 4-5 centimeter free end. Then we take the thick free end of the underbrush with our right hand and wind the cord, the tube with the understory by means of five neat turns, which should fit tightly to each other. Now wrap the forefinger and the thumbs of the left hand around the turns so that they do not untwist when the thick end of the underbrush is passed, from right to left, into the tube. We pull out the tube neatly in the left-hand direction. Tighten the knot halfway, pull out the two ends of the underbrush gently and in no case pull the cord. We check that the coils adjoin each other tightly and evenly. Next, wet the knot, tighten it, for this, pulling the two ends of the undergrowth. This knot should tightly crimp the outer braid of the cord while bumping into it. To fasten the assembly permanently, pull the cord and undergrowth in different directions. Cut off the extra ends of the underbrush and cord.

Arbor Knot

How to tie a cord to a reel? The most common and common way to attach a cord to a coil is the Arbor Knot. The technique of its execution is as follows. We fasten the usual knot at the very end of the cord, then tighten it tightly. Then we extend the cord through the coil so that its end with the knot is lower down from the spool, we tie the cord with the same end. Everything is done with the help of a normal node. After all this, tighten the second knot tightly, then tighten the loop located on the spool, pulling the cord for the free end.

The "Trailin" node

To learn how to tie a cord to a swivel, you can by studying the technique of knotting the "Trailin" node. This method also refers to one of the most durable and reliable for fastening the cord to swivels, hooks, artificial baits. Trailin's peculiarity is that he does not slip.

To tie such a knot, you must double-pass the end of the cord through the hook eyelet. Then wrap the end of the rope five or six times around the root end. Then we pass through the initially formed double loop, which is near the hook, the remaining end. By water we moisten the knot, we tighten it, we cut the end not very shortly. For insurance, the length of the end should be a minimum of 3-4 mm.

Double grinner knot

How to tie a cord to a line? This kind of knot is used to link two identical diameter along the diameter or with slightly different diameter of the lines, and also to bind the cord and line.

Technique of the unit is as follows. Fold the fishing line and cord together, so that their ends are located to meet each other. Now we take the end of the line, from it we form a loop. We wind the cord and formed loop. We make about 5-6 turns, from the loop we deduce the end of the line. We wet the knot and tighten it well. The same manipulations are carried out with the end of the cord. As a result, you will get two nodes, which you need to pull together towards each other. Surplus of each end is cut off, leaving somewhere 1-2 cm.

The "Palomar"

How to tie the hook to the cord? "Palomar" is a knot with which the hook is attached to the line (cord), the fly to the leader (leash). This is one of the nodes, consisting of a group of proven, reliable and durable fishing knots. He is tied up like this. Bend the end of the cord in half so that the loop turns flat and open. We bend the bent end through the hook, more precisely through its eyelet. We take this same bent end and form a simple knot on the cord. The bend of the cord is passed over the hook, then over and into the girth of the nodule. Wet the knot with water, tighten the ends to fix it. Shorten the ends if necessary.

When the loop is already passed through the eye, it is necessary to tie a simple knot with this loop. In this case, the loop will pass through the hook and tighten under the eyelet around the loop. The result is a free, for rotation in the node, position.

Hanging loop

How to tie a carbine to the cord? Such a node forms a loop, which is at an angle of 90 degrees to the middle of the cord. The hanging loop is convenient for tying carbines, swivels, hooks and other fishing tackle to the main line, cord, cone underbrush (leader) to provide a backup attachment to the additional fly.

The described node is tied like this. We form a large loop in the middle of the cord. The center is held with a finger and wraps around this point of the loop a loop somewhere six times. We make a hole in the center, through which we pass a loop. Hold the loop with your teeth, lubricate the knot with water and tighten it.

Wetting with water and tightening the knot, we change its structure. Pulling on each rope, the turns that have been twisted, you can regroup the twist so that the inner thread will act as the outer thread.