How to sew shoes with your own hands?

The success of any walk or travel depends largely on the strength and reliability of the shoes. For example, going on a hike, you need to be completely confident that sneakers or shoes that seem strong at the most responsible or inopportune moment will not fall apart.

Unfortunately, there are not many quality and durable shoes on sale, so it's better to stitch it before walking or traveling. How to sew shoes, we'll talk further.

Is it worth it?

To sew shoes is possible, as a rule, almost to every man and even women. But sometimes it's just not advisable. On modern footwear, due to the low quality of rubber, it often happens that simple firmware soles are not enough, and it requires a complete replacement. In order to understand if there is any sense in this operation, an evaluation of the degree of wear of the sole should be made in advance. If you can not do it yourself, you can try to consult a shoe repairman, ask you to estimate the amount of work and the cost. As a rule, the master stipulates the forthcoming operations and honestly warns the customers that the sole must be replaced or there will be enough firmware.

How to sew shoes with your own hands?

To repair shoes, it is not necessary to carry it to the master in a shoe shop, you just need to know how to do it yourself. Even without special skills, you can perform minor repairs yourself. So, let's look at how to sew shoes with an awl and crochet and what is needed for this?

What is needed?

In order to flush the sole qualitatively, it is necessary to purchase a specialized hook, rubber glue and nylon threads of suitable thickness. The manufacturer and brand of rubber glue are not particularly important, but the thickness of the threads must be matched correctly, since too thin cut the material, and the thick ones will look very ugly and rude. The most optimal is the average thickness. The thread color should be chosen the same as the color of the sole itself, or choose a contrasting shade, if the firmware also performs a decorative role.

To buy a shoe hook is also not a problem, but you can do it yourself if necessary.

It is also necessary to stock up with an awl, in order to make holes in places where it is difficult to make a crochet. In addition, it is recommended to prepare a small piece of chalk or soap, which will mark the line firmware. The line will then be smooth and beautiful.

Preparatory work

Before shoeing, first you need to clean it and glue the fallen off sole with a special rubber glue. This is done so that the shoes through the firmware do not gain water. Glue after a lot of cleaning is not necessary, since they will need to smear the thread in the places of insertion, further sealing the shoes and the seam.

Then, on the sole, draw a future seam line, retreating from the junction about one third of the side of the sole. On some shoes, there is a special groove on the sole that facilitates obtaining a smooth seam. In this case, you do not need to draw a line.

You can start sewing. How to properly sew the shoes, we'll look further. Remember that the seam is better to start near the heel.

Firmware

So, let's see how to patch shoes.

In the left hand, you need to place a sweep, and with your right hand take an awl. Make a hole in the place where the stitch will begin. The awl should be pinched at an angle of approximately 45 degrees. To avoid injury when piercing, the arm from the line of the awl should be carefully removed.

Then you need to prepare the prepared thread for folding in half. Connect the ends so that they coincide. From the inside of the shoe through the hole you need to hold a hook, throw a thread on it from the thread and drag it so that the ends are left outside. After approximately 5 mm, a similar hole should be made and the free ends of the thread extended through it. Pull out the loop and thread the outer end of the thread from the previous stitch. Tighten the loop from the outside. Make the 3rd hole and repeat the above steps. At the end of the process for securing the seam to make a pair of reverse stitches. Tie a nylon and cut off excess.

So, we looked at how to sew shoes. Using this simple method, you can sew almost any shoes. And this, albeit small, but still saving.

How to make a hook yourself?

1. We make a handle and drill a hole in it with a depth equal to the height of 8 mm of the bolt.
2. We prepare the bolt, which will serve as a nozzle for different rods. To do this, drill a 2.5 mm drill in its hat with 2 holes - the first depth of about 2-3 cm is directed to the inside of the bolt, the second - to the side in the cap.
3. Bolt is attached to the handle. Than he zasyadet denser, the better.
4. Thread. A tap in a lateral aperture under a three-millimeter bolt we cut a carving.
5. Preparing the rod. To do this, take the bicycle needle, cut to the desired length. With a hammer we flatten the end, we cut out a notch for the thread in the middle of the flattened section. The groove can be made a small Bulgarian with a diamond disc or nadfile. The notch must be made at an angle and directed to the point, so that it is convenient to grasp the thread. After the notch is made, sharpen the point. To get rid of small burrs, which will interfere with work, take a nylon thread, apply a grinding paste mixed with a drop of machine oil. Clamp the rod in a vice upward with the point and hook the thread behind the notch. Drive the thread from side to side for about 20 minutes. The groove will acquire a perfectly flat surface.

The hook is ready. How to sew shoes is described above.