How to make an electrolyzer with your own hands?

Modern electrolyzers are actively used in the industrial sphere. The data of the device for participation in the production of active metals have been created. In particular, it is possible to note magnesium. This is due to electrolysis. Also, this device is capable of participating in the production of active non-metals. Of these, you can select chlorine and fluorine.

Motorists also use electrolysis in order to increase the resistance of the metal. A special protective layer is formed on its surface. From corrosion of metal to save the car it is capable. There are models of different types, and in order to assemble the electrolyzer of hydrogen by oneself, it is necessary to familiarize yourself with the basic configurations.

Model with two filters

Folding this type of electrolyzer for a car with their own hands is quite simple. First of all, you need to prepare four sheets of metal. In this case, it is possible to use galvanized steel. In this case, the stainless steel for the electrolysers is also suitable. After this, a container of water is installed directly. The holes in it can be made with a knife. Further, in order to make an electrolyzer by hand, it is important to fix the filters. You can use the usual mesh type.

In the store to buy it will not be difficult. The next step is to fix the non-return valve. To do this, the container must be secured on a basis. To do this, many experts advise using bolts. Next, it remains to put a board with a thickness of not more than 2.3 mm. The next step is fixing the bubble tube. It is important to monitor the water level in the container. The nozzle is installed last. The shutter in this case should be located on the side of the board. The terminals are attached only after the gasket is attached.

Top Container Device

To assemble this type of electrolyzer for a car with your own hands, you must first prepare the board. Most often they are used in stainless steel. However, galvanized species also come across. In this case, the thickness of the boards should not exceed 2.2 mm. After they are twisted with screws, it is necessary to fix the insulating lining. All this is done in order to protect the lower shutter.

Next, to make an electrolyzer with your own hands, the upper board is installed. Its thickness should not exceed 1.2 mm. The check valve in this case is important to install on the protective ring. Thus, water leaks will occur rarely. The next step is fixed directly to the container. For this, many experts recommend using fittings. The bubble tube in the device is attached last. Then, electrodes with terminals are installed.

Model with the bottom location of the container

To make this type of electrolyzer for cars with their own hands, the container is more expedient to choose plastic. However, today it is possible to meet and aluminum modifications. To weigh in this case the device will be quite a lot. Begin the assembly with the installation of the base. This will require only one sheet of stainless steel. Its dimensions must correspond to the dimensions of the container. After installing it, it is possible to fasten the top board.

In dimensions, it must correspond to the dimensions of the bottom sheet of metal. After this, the tube is installed directly. Filters in this case do not need to be used. The next step is to fix the bolt. It should be fixed directly to the bottom plate on the screws. Select them more appropriately with the marking M6. To date, finding them in the store is quite simple. After that, the nozzle is fixed directly. To this end, many experts recommend installing fittings. In turn, the filters are better to fix with the help of plastic clips. However, do not forget to use a rubber gasket. Otherwise, the insulation of the device will be broken.

Device with two valves

Make an electrolyzer with your own hands (the drawings are shown below) on two valves is quite simple. AT

The first step should be to prepare the basis. For this purpose, it is best to choose a strong sheet of metal. On the width it should converge with the plastic container. After that, the board is fixed directly. At this stage, it is important to firmly bond all the sheets. For this, you can use screws with the M6 marking. However, much in this case depends on the dimensions of the container.

The next step is to install a tube of bubbling type. Its diameter must be at least 3.3 cm. After that, the shutter is selected for the device. The first valve must be installed at the base of the pipe. Fix it on the inner surface using fittings. After that, a clamping ring is used. Then another metal platinum is installed to secure the shutter. Then it remains to fix the second valve to the pipe. The distance from the edge should be at least 2 cm.

Models for three valves

To make an electrolyzer with your hands in the machine for three valves, it is necessary to prepare a strong plate. Stainless steel in this case is ideal. The first valve can be installed directly on the inlet pipe, which is connected directly to the container. After that, the upper plate is fixed. Next, the second bubble tube is installed. At the end, there must be another valve.

To fix it, many experts recommend using a clamping ring. In this case, the fitting must be fixed quite rigidly. The next step is to prepare the shutter for the device. Only after this, the third valve is attached to the pipe and connected to the nozzle. At this stage it is necessary to use hairpins. Also, many experts recommend the use of special rubberized gaskets for insulation.

Device with zinc plated board

Electrolyzer for heating by their own hands is often collected with galvanized boards. To date, it is very in demand. In order to begin work, a small plate is prepared. After that, a container is selected for it. Connect the boards to each other with screws. All in all, they need four units.

After this, it is possible to start fixing the upper insulating gasket. For the rapid implementation of the electrolysis process, many experts recommend using only plastic containers. You can fix them on the basis with the help of studs. After that, it remains only to install the gate with the terminals for connection.

Model with plexiglas

Folding the cell with your own hands from Plexiglas is very difficult nowadays. First of all, the problem is that it is very difficult to process. It should also be noted that it is necessary to select the container of the correct size for it. In total on the board, you need to make four holes in the corners. After this, metal plates are placed at intervals of 1.5 cm. Then you can fix the shutter directly. For insulation, many experts recommend the use of rubberized gaskets, but please note that their thickness should not exceed 2 mm.

Model on electrodes

The electrolyzer of water with its own hands on the electrodes is quite simple. In this case, it is more expedient to begin work with the assembly of the lower part of the device. A small metal plate is prepared for this purpose. After that, you can fasten the bolt. In this case, the container will be located in the upper part. The next step is to fix the tube directly. You can arrange two filters in it. In this situation, much depends on the size of the container. After this, it is possible to fix the nozzle.

The next step is to install the top sheet of metal. At this stage, it is important to ensure that the plate does not come into contact with the container. In this case, the clamping screws from it must be located at a distance of about 2 cm. The electrodes in this case must be fixed to the bolt. In this case, the terminals are best placed on the other side.

Application of plastic washers

Make an electrolyzer with your own hands with plastic gaskets is possible if you pick up a good aluminum container. In this case, its isolation will be achieved high. Start the assembly of the device immediately after installing the base. After that, the gaskets must be placed. At this stage, they need to cut out a rectangular shape.

In total, four gaskets are needed for assembly. They should be installed in the corners, and the clearance should be about 2 mm. After this, it will be possible to lock the container. For this purpose, take the second sheet and make four holes in it. They are necessary in order to fix the container with screws. They are most often used with the M6 marking. In this case, it is better to use rubber rings for good fixation. After that, it will remain to install the shutter, as well as the terminals for connecting the device.

Model on two contact terminals

Models of this type must be added from the base. For this, the plate can be taken aluminum or steel. After that it is important to fix the plastic container on the cylinders. You can also use screws. Then it remains to install the shutter. The nozzle in this case can be of needle type. Its diameter should be at least 3 mm.

The terminals in the device are attached directly to the bottom board. For this, conventional conductors are used. The tube should be installed last. At this stage it is important not to forget about the clamping ring. The filters for the electrolyzer are best suited for mesh type. There should be two valves in the system. They are attached to the spindles.